Toshiba Satellite Pro A210 Maintenance Manual - Page 168

Replacement Procedures, 6 MDC Module, CAUTION

Get Toshiba Satellite Pro A210 PDF manuals and user guides View all Toshiba Satellite Pro A210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 168 highlights

4 Replacement Procedures 4.6 MDC Module Installing the MDC Module Install the MDC module according to the following procedures and Figures 4-13, after checking that the computer is turned off in boot mode. CAUTION: Install the MDC module after turning off the computer. If this is violated, the computer or MDC module can be damaged. CAUTION: Do not touch the connectors on the MDC module or in the computer. Contaminated connectors can cause MDC module failures. 1. Connect the MDC cable to connector JP1 on the MDC module. 2. Connect the MDC module to CN4 on the system board. 3. Secure the MDC module with two M2x3 white bind screws. Note: After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed MDC module has been recognized by the system. If it has not been recognized yet, check the connections. 4-28 Satellite A210/A215/Satellite Pro A210/EQUIUM A210/SATEGO A210 Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
4 Replacement Procedures
4.6 MDC Module
4-28
Satellite A210/A215/Satellite Pro A210/EQUIUM A210/SATEGO A210
Maintenance Manual
Installing the MDC Module
Install the MDC module according to the following procedures and Figures 4-13, after
checking that the computer is turned off in boot mode.
CAUTION
:
Install the MDC module after turning off the computer. If this is violated, the
computer or MDC module can be damaged.
CAUTION
:
Do not touch the connectors on the MDC module or in the computer.
Contaminated connectors can cause MDC module failures.
1.
Connect the MDC cable to connector JP1 on the MDC module.
2.
Connect the MDC module to CN4 on the system board.
3.
Secure the MDC module with two M2x3 white bind screws.
Note: After the computer is turned on, check the hardware configuration in the
Hardware Setup or TSETUP program to make sure that the installed MDC module has
been recognized by the system. If it has not been recognized yet, check the connections.