Toshiba TLP 780 Owners Manual - Page 23

Connecting a computer (COMPUTER IN 2 connector ), Installation and, connection

Page 23 highlights

Installation and connection Connecting a computer (COMPUTER IN 2 connector) CONTENTS 23 You can project the picture of analog RGB or digital RGB signal from a computer by using COMPUTER IN 2 connector. Check that the power for the projector and computer is off before connecting the cables. USB MONITOR OUT CONTROL COMPUTER IN 1 ( Y/PB/PR ) COMPUTER IN 2 AUDIO IN VIDEO IN R - AUDIO - L VIDEO S-VIDEO COMPUTER IN 2 Connector (DVI connector) For use as both Analog RGB (2) input and Digital RGB input. At shipping from factory, it is set for use as Analog RGB (2) input. Change the setting on the menu screen when using as Digital RGB input. 45 AUDIO IN jack For use as both audio signals for RGB input (analog RGB (1)/analog RGB (2)/digital RGB) and Y/PB/PR input. Connecting a Mac adapter for Macintosh computers (Supplied) To COMPUTER IN 2 Connector Be sure to connect in the proper direction. Computer To monitor port DVI analog cable (Supplied) To AUDIO IN jack Audio cable (Supplied) φ3.5mm Stereo mini-jack To audio output port Notes (Please also read "Notes" on page 22.) • DVI digital cable should be purchased separately when you input a digital RGB signal. • Although infrequent, noise might be generated on the screen depending on the type of computer and the connection cables. Should this occur, reduce the refresh rate of the computer signal, or lower the resolution. Use of connection cables that are 2 m or shorter is recommended. • The input signal specifications of the DVI port of the projector conform to DVI 1.0 specifications; however, contents protection is not supported. Note that there is no guaranty of the operations not specified in this specifications. Continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80

23
Installation and
connection
Continued
USB
COMPUTER IN 1
COMPUTER IN 2
S-VIDEO
VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN
(
Y/P
B
/P
R
)
MONITOR
OUT
CONTROL
You can project the picture of analog RGB or digital RGB signal from a computer by using COMPUTER IN 2 connector.
Check that the power for the projector and computer is off before connecting the cables.
COMPUTER IN 2 Connector (DVI connector)
For use as both Analog RGB (2) input and Digital RGB input. At shipping
from factory, it is set for use as Analog RGB (2) input. Change the setting on
the menu screen when using as Digital RGB input.
AUDIO IN jack
For use as both audio signals for RGB input (analog RGB (1)/analog RGB
(2)/digital RGB) and Y/P
B
/P
R
input.
(Please also read "Notes" on page 22.)
• DVI digital cable should be purchased separately when you input a digital RGB signal.
Although infrequent, noise might be generated on the screen depending on the type of computer and the connection cables. Should this occur, reduce
the refresh rate of the computer signal, or lower the resolution. Use of connection cables that are 2 m or shorter is recommended.
• The input signal specifications of the DVI port of the projector conform to DVI 1.0 specifications; however, contents protection is not supported. Note
that there is no guaranty of the operations not specified in this specifications.
Connecting a computer
(COMPUTER IN 2 connector)
Computer
To monitor port
DVI analog cable
(Supplied)
To AUDIO IN jack
Audio cable (Supplied)
φ
3.5mm Stereo mini-jack
To audio output port
To COMPUTER IN 2 Connector
Be sure to connect in the proper
direction.
Connecting a Mac adapter for
Macintosh computers (Supplied)
45
Notes