Toshiba TLP-WX2200U Owners Manual - Page 12

Connection, Label locations

Page 12 highlights

Preparations Connection Before connection • Read the owner's manual of the device you are connecting to the projector. • Some types of computer cannot be used or connected to this projector. Check for an RGB output terminal, supported signal p.52 , etc. • Turn off the power of both devices before connecting. • The figure is a sample connection. This does not mean that all of these devices can or must be connected simultaneously. (Dotted lines mean items can be exchanged.) Computer (for control) Video recorder, DVD player, etc. Computer Computer To RS-232C p.54 terminal To audio output White (L)/Red (R) Audio cable (not supplied) Control cable To S-video output S-video cable (not supplied) To audio output Audio cable (not supplied) To audio output To RGB output Audio cable (not supplied) RGB cable (supplied) To RGB output RGB cable (not supplied) Monitor Notes • When COMPUTER 2 IN terminal (also used for MONITOR OUT terminal) is used as MONITOR OUT terminal, the signal which is input to COMPUTER 1 IN terminal is output. • Signals are output from MONITOR OUT terminal even in standby mode. However, from AUDIO OUT terminal, no audio signal is output. • A computer monitor cannot accept Y/PB/PR signals correctly. • The AUDIO IN terminal doubles for devices connected to COMPUTER 1 terminal and COMPUTER 2 terminal. • When an AUDIO OUT terminal is connected, sound is not output from the projector speaker. • Output volume of AUDIO OUT terminal can be adjusted by the VOL button. • Moving pictures played back on computers using DVD software may appear unnatural if it is projected with this projector, but it is not a malfunction. Label locations To audio output White (L)/ Red (R) AV cable (not supplied) To video output Video recorder, etc. Audio cable (not supplied) Audio cable (not supplied) To audio input White (L)/Red (R) To audio output It is necessary to switch to MONITOR OUT by the switch. p.18 Monitor cable Mini D-sub 15P-BNC (not supplied) To Y/CB/CR output Green (Y)/Blue (CB)/Red (CR) Conversion adapter BNC-pin (not supplied) Audio amplifier, etc. DVD video recorder, etc. Or Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. 22 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29

23
22
Preparations
p.54
Video recorder,
DVD player, etc.
To audio output
White (L)/Red (R)
S-video cable
(not supplied)
To S-video output
Before connection
Read the owner’s manual of the device you are connecting to the projector.
Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal
p.52
, etc.
Turn off the power of both devices before connecting.
The figure is a sample connection. This does not mean that all of these devices can or
must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Connection
Computer
(for control)
Computer
To
RS-232C
terminal
Audio cable
(not supplied)
To audio output
Control cable
RGB cable
(supplied)
To RGB
output
Computer
Audio cable
(not supplied)
To audio
output
Audio cable
(not supplied)
RGB cable
(not supplied)
To RGB
output
Audio amplifier, etc.
DVD video recorder, etc.
Video recorder, etc.
Conversion
adapter BNC-pin
(not supplied)
Monitor cable Mini
D-sub 15P-BNC
(not supplied)
To audio input
White (L)/Red (R)
AV cable
(not supplied)
To video
output
Audio cable
(not supplied)
Audio cable
(not supplied)
To audio
output
To Y/C
B
/C
R
output
Green (Y)/Blue
(C
B
)/Red (C
R
)
To audio
output
White (L)/
Red (R)
It is necessary to
switch to MONITOR
OUT by the switch.
Monitor
p.18
Notes
When COMPUTER 2 IN terminal (also used for MONITOR OUT terminal) is used as
MONITOR OUT terminal, the signal which is input to COMPUTER 1 IN terminal is output.
Signals are output from MONITOR OUT terminal even in standby mode.
However, from AUDIO OUT terminal, no audio signal is output.
A computer monitor cannot accept Y/P
B
/P
R
signals correctly.
The AUDIO IN terminal doubles for devices connected to COMPUTER 1 terminal and
COMPUTER 2 terminal.
When an AUDIO OUT terminal is connected, sound is not output from the projector
speaker.
Output volume of AUDIO OUT terminal can be adjusted by the
VOL
button.
Moving pictures played back on computers using DVD software may appear unnatural if it
is projected with this projector, but it is not a malfunction.
Label locations
Caution
– use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
Or