Tripp Lite SU1500RTXLCD2U Owner's Manual for Single-Phase Online Rack UPS with - Page 6

Tower Mounting 750-2200VA Models Only - battery

Get Tripp Lite SU1500RTXLCD2U PDF manuals and user guides View all Tripp Lite SU1500RTXLCD2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Installation 2-Post Mounting If you mount 2U UPS models in 2-post racks, they require the addition of a Tripp Lite 2-Post Rackmount Installation Kit (model: 2POSTRMKITWM, sold separately). 3U UPS models can also be mounted in 2-post racks, but require the addition of 2POSTRMKITHD (sold separately). See Installation Kit owner's manual for installation procedure. Tower Mounting (750-2200VA Models Only) Your UPS can be mounted in an upright tower position with optional base stands sold separately by Tripp Lite (Model # 2-9USTAND). When mounting the UPS on adjustable base stands, make sure that the control panel is toward the top. The control panel may be rotated to make it easier to read. Insert a small screwdriver or similar tool in the slots on either side of the panel, pop it out, rotate it, and pop it back into place as shown. Front panel setup should be operated by service personnel only. WARNING! All UPS systems are extremely heavy. Use caution when lifting and mounting. User must properly stabilize the UPS when lifting and mounting. Note: SU3000RTXLCD3U cannot be tower-mounted. Doing so will inhibit the UPS system's internal cooling. Model SU750RTXLCD2U, SU1000RTXLCD2U UPS Dimensions (HxWxD in.) 3.5 x 17.5 x 13.5 UPS Dimensions (HxWxD cm.) 8.8 x 44.4 x 34.3 Operating Altitude: 0 to 3000 m (0 to 10,000 ft.) SU1500RTXLCD2U 3.5 x 17.5 x 19 8.8 x 44.4 x 48.3 SU2200RTXLCD2U 3.5 x 17.5 x 19 8.8 x 44.4 x 48.3 SU3000RTXLCD3U 5.25 x 17.75 x 26 13.3 x 45 x 66 EXTERNAL BATTERY CONFIGURATION NOTE If external battery packs are to be used with this UPS, install them following the mounting/installation documentation included with each battery pack. External battery pack installation requires the UPS be configured one of two ways: 1. Via the UPS front panel LCD interface 2. Via Tripp Lite's EXTERNAL BATTERY CONFIGURATION software This UPS is factory programmed with discharge curves and charging profiles for two basic external battery pack configurations accessible using the UPS front panel LCD interface. Additional battery pack options using larger or multiple external battery packs are also supported, but require configuration using Tripp Lite's EXTERNAL BATTERY CONFIGURATION software and a serial port connection to the UPS. See page 23 to determine which method applies to your external battery pack configuration. 6 12-488-93-3156.indb 6 9/12/2012 3:56:54 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
6
Installation
2-Post Mounting
If you mount 2U UPS models in 2-post racks, they require the addition of a Tripp Lite 2-Post Rackmount Installation Kit (model:
2POSTRMKITWM, sold separately). 3U UPS models can also be mounted in 2-post racks, but require the addition of 2POSTRMKITHD
(sold separately). See Installation Kit owner’s manual for installation procedure.
Tower Mounting (750-2200VA Models Only)
Your UPS can be mounted in an upright tower position with
optional base stands sold separately by Tripp Lite (Model #
2-9USTAND). When mounting the UPS on adjustable base stands,
make sure that the control panel is toward the top. The control
panel may be rotated to make it easier to read. Insert a small
screwdriver or similar tool in the slots on either side of the panel,
pop it out, rotate it, and pop it back into place as shown. Front
panel setup should be operated by service personnel only.
WARNING!
All UPS systems are extremely heavy. Use caution when
lifting and mounting. User must properly stabilize the UPS
when lifting and mounting.
Note: SU3000RTXLCD3U cannot be tower-mounted. Doing so will inhibit the UPS
system’s internal cooling.
Model
SU750RTXLCD2U,
SU1000RTXLCD2U
SU1500RTXLCD2U
SU2200RTXLCD2U
SU3000RTXLCD3U
UPS Dimensions (HxWxD in.)
3.5 x 17.5 x 13.5
3.5 x 17.5 x 19
3.5 x 17.5 x 19
5.25 x 17.75 x 26
UPS Dimensions (HxWxD cm.)
8.8 x 44.4 x 34.3
8.8 x 44.4 x 48.3
8.8 x 44.4 x 48.3
13.3 x 45 x 66
Operating Altitude: 0 to 3000 m (0 to 10,000 ft.)
EXTERNAL BATTERY CONFIGURATION NOTE
If external battery packs are to be used with this UPS, install them following the mounting/installation documentation included with each
battery pack. External battery pack installation requires the UPS be configured one of two ways:
1. Via the UPS front panel LCD interface
2. Via Tripp Lite’s EXTERNAL BATTERY CONFIGURATION software
This UPS is factory programmed with discharge curves and charging profiles for two basic external battery pack configurations accessible
using the UPS front panel LCD interface. Additional battery pack options using larger or multiple external battery packs are also
supported, but require configuration using Tripp Lite’s EXTERNAL BATTERY CONFIGURATION software and a serial port connection to the
UPS. See page 23 to determine which method applies to your external battery pack configuration.
12-488-93-3156.indb
6
9/12/2012
3:56:54 PM