Tripp Lite SUINT3000LCD2U Owner s Manual for Single-Phase Rackmount On-line UP - Page 5

Tower Mounting 1000-2200VA Models Only

Get Tripp Lite SUINT3000LCD2U PDF manuals and user guides View all Tripp Lite SUINT3000LCD2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Installation Tower Mounting (1000-2200VA Models Only) Your UPS can be mounted in an upright tower position with optional base stands sold separately by Tripp Lite (model: 2-9USTAND). When mounting the UPS on adjustable base stands, make sure that the control panel is toward the top. The control panel may be rotated to make it easier to read. Remove the 4 front screws from the front panel and take it off. Pinch the tabs located on the sides of the LCD panel, and then rotate it. Replace the front panel and secure it. Front panel setup should be operated by service personnel only. WARNING! All UPS systems are extremely heavy. Use caution when lifting and mounting. User must properly stabilize the UPS when lifting and mounting. UPS Model SUINT1000LCD2U UPS Dimensions (HxWxD in.) 3.4 x 17.25 x 15.60 UPS Dimensions (HxWxD cm.) 8.6 x 43.8 x 39.6 Operating Altitude: 0 to 3000 m (0 to 10,000 ft.) SUINT1500LCD2U 3.4 x 17.25 x 19.6 8.6 x 43.8 x 49.6 SUINT2200LCD2U 3.4 x 17.25 x 19.6 8.6 x 43.8 x 49.6 SUINT3000LCD2U / SU3000LCD2UHV 3.4 x 17.25 x 24.25 8.6 x 43.8 x 61.6 EXTERNAL BATTERY CONFIGURATION NOTE If external battery packs are to be used with this UPS, install them following the mounting/installation documentation included with each battery pack. External battery pack installation requires the UPS be configured one of two ways: 1. Via the UPS front panel LCD interface 2. Via Tripp Lite's EXTERNAL BATTERY CONFIGURATION software This UPS is factory programmed with discharge curves and charging profiles for external battery pack configurations accessible using the UPS front panel LCD interface. Additional battery pack options using larger or multiple external battery packs are also supported, but require configuration using Tripp Lite's EXTERNAL BATTERY CONFIGURATION software and a serial port connection to the UPS. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
5
Installation
Tower Mounting (1000-2200VA Models Only)
Your UPS can be mounted in an upright tower position with
optional base stands sold separately by Tripp Lite (model:
2-9USTAND). When mounting the UPS on adjustable base stands,
make sure that the control panel is toward the top. The control
panel may be rotated to make it easier to read. Remove the 4
front screws from the front panel and take it off. Pinch the tabs
located on the sides of the LCD panel, and then rotate it. Replace
the front panel and secure it. Front panel setup should be
operated by service personnel only.
WARNING!
All UPS systems are extremely heavy. Use caution when
lifting and mounting. User must properly stabilize the UPS
when lifting and mounting.
UPS Model
SUINT1000LCD2U
SUINT1500LCD2U
SUINT2200LCD2U
SUINT3000LCD2U / SU3000LCD2UHV
UPS Dimensions
(HxWxD in.)
3.4 x 17.25 x 15.60
3.4 x 17.25 x 19.6
3.4 x 17.25 x 19.6
3.4 x 17.25 x 24.25
UPS Dimensions
(HxWxD cm.)
8.6 x 43.8 x 39.6
8.6 x 43.8 x 49.6
8.6 x 43.8 x 49.6
8.6 x 43.8 x 61.6
Operating Altitude: 0 to 3000 m (0 to 10,000 ft.)
EXTERNAL BATTERY CONFIGURATION NOTE
If external battery packs are to be used with this UPS, install them following the mounting/installation documentation included with each
battery pack. External battery pack installation requires the UPS be configured one of two ways:
1. Via the UPS front panel LCD interface
2. Via Tripp Lite’s EXTERNAL BATTERY CONFIGURATION software
This UPS is factory programmed with discharge curves and charging profiles for external battery pack configurations accessible using the
UPS front panel LCD interface. Additional battery pack options using larger or multiple external battery packs are also supported, but
require configuration using Tripp Lite’s EXTERNAL BATTERY CONFIGURATION software and a serial port connection to the UPS.