Troy-Bilt TB516 Operation Manual
Troy-Bilt TB516 Manual
 |
View all Troy-Bilt TB516 manuals
Add to My Manuals
Save this manual to your list of manuals |
Troy-Bilt TB516 manual content summary:
- Troy-Bilt TB516 | Operation Manual - Page 1
TB516 EC Electric Start Capable 4-Cycle Lawn Edger Operator's Manual English - Page 1 Remove Unit From Carton Assemble The Unit NO TOOLS REQUIRED! 1 Remove all contents from the carton. Assemble The Unit 2 Slide the ends of - Troy-Bilt TB516 | Operation Manual - Page 2
TABLE OF CONTENTS Service Information 2 Safety Information 2 Oil and Fuel Information 3 Starting and Stopping Instructions 3 Operating Instructions 3 Maintenance and Repair Instructions 3 Cleaning and Storage 4 Optional Accessory 4 Troubleshooting 4 Specifications 4 Warranty Information - Troy-Bilt TB516 | Operation Manual - Page 3
. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to a Troy-Bilt or other qualified service dealer. NOTE: Maintenance, replacement, or repair of the emission - Troy-Bilt TB516 | Operation Manual - Page 4
) Rocker Arm Feeler Gauge 11. Replace the spark plug wire. 12. Reinstall the engine cover. Check alignment of the cover before tightening the screws. Tighten screws. Valve Stem Fig. 23 4 Electric Start Feature TROUBLESHOOTING PROBLEM THE ENGINE WILL NOT START Empty fuel tank Primer bulb was - Troy-Bilt TB516 | Operation Manual - Page 5
TB516 EC Recortador de bordes de césped de 4 tiempos con posibilidad de arranque eléctrico Manual del Operador se puede usar durante este tiempo. Español - Page 5 IMPORTANTE: LEA BIEN EL MANUAL DEL OPERADOR Y, AL OPERAR LA UNIDAD, SIGA LAS INSTRUCCIONES PARA EL FUNCIONAMIENTO SEGURO. ¿NECESITA - Troy-Bilt TB516 | Operation Manual - Page 6
manos cuando la opere. Mantenga un agarre firme sobre ambas manijas. • Mantenga las manos, la cara y los pies alejados de todas las partes en movimiento. No limpio, nuevo y sin plomo. • INDICADOR DE ACEITE Consulte el manual del operador para obtener información acerca del tipo correcto de aceite. - Troy-Bilt TB516 | Operation Manual - Page 7
para evitar lesionarse con el rociado del combustible. No opere nunca la unidad sin la tapa del combustible firmemente colocada parte trasera de la unidad. Consulte la sección de Operación del manual del operador del Arrancador Eléctrico o Accesorio de Arranque Eléctrico Opcional Power Start - Troy-Bilt TB516 | Operation Manual - Page 8
tabla. Deben ser incluidos como parte de toda puesta a punto de cada temporada. NOTA: Es posible que algunos procedimientos de mantenimiento requieran herramientas o habilidades especiales. Si no está seguro sobre estos procedimientos, lleve la unidad a un Troy-Bilt o a otro proveedor de servicio - Troy-Bilt TB516 | Operation Manual - Page 9
arrancarse con un opcional arrancador eléctrico o Power Start Bit™ (Se vende por separado). Si decide arrancar * Toda las especificaciones contenidas en este manual se basan en la información más reciente disponible en el momento de impresión del manual. Nos reservamos el derecho de hacer cambios - Troy-Bilt TB516 | Operation Manual - Page 10
NOTES 10 - Troy-Bilt TB516 | Operation Manual - Page 11
NOTES 11 - Troy-Bilt TB516 | Operation Manual - Page 12
in the following cases: A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters B. Wear items - Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars, Cultivator Tines. C. Troy-Bilt does not extend any warranty for products sold
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
Remove Unit From Carton
Start The Unit
Assemble The Unit
Remove the oil plug from the
crankcase, and pour the
entire bottle of oil into the fill
hole.
Place unit on a level surface
and fill fuel tank.
DO NOT
overfill.
For cold weather conditions
(below 40°F), push the red
cold weather start lever
down to the closed position.
DO NOT
push this lever
down if the temperature is
above 40°F.
Press
primer bulb
10 times
,
or until fuel is visible
Stand in the starting
position.
Pull the starter rope in a
controlled motion until the
unit starts.
Wait
60 seconds.
For cold weather conditions
(below 40°F), pull the red
cold weather start lever
back up to the open position
after the unit starts.
Tip the unit back so the
blade does not touch the
ground. Squeeze the throttle
control and allow the engine
to warm up for
30 to 60
seconds. The unit may be
used during this time.
1
1
Remove all contents from
the carton.
5
6
7
1
9
10
DO NOT
squeeze the
throttle.
8
Start The Unit
11
12
13
Align the holes on the upper
shaft with the holes on the
middle shaft. Insert bolts
into the two holes. Install a
washer and knob onto each
bolt. Tighten the knobs
securely. Make sure the “V”
bend in the handle is
pointing up.
3
Slide the ends of the middle
shaft over the ends of both
lower shafts and align the
holes. Insert bolts into the
two holes. Install a washer
and knob onto each bolt.
Tighten the knobs securely.
Keep the cables to the front
of the unit.
2
4
Primer Bulb
10 X
Red Cold Weather
Start Lever
Assemble The Unit
Pull the starter rope through
the eye hook.
Insert the cables into the cable
restraints on the lower and
upper shafts.
DIDN’T START?
IF
the engine does not start,
go back to step 9.
IF
the engine stops while
squeezing the throttle, go
back to step 10.
IF
the engine is hot,
go back to step 9.
Starter
Rope Grip
Fuel Cap
Throttle
Control
On/Off
Control
Handle
Air Filter
Cover
Primer
Bulb
Oil Fill
Plug
Spark Plug
Edger Blade
Blade Shield
Depth
Adjustment Lever
NO TOOLS REQUIRED!
Red
Cold Weather
Start Lever
Red Cold Weather
Start Lever
769-07491 P00
10/11
NEED HELP?
CALL 1-800-828-5500 IN U.S. OR 1–800–668–1238 IN CANADA
TB516 EC
Electric Start Capable
4-Cycle Lawn Edger
English — Page 1
Español — Page 5
Operator’s Manual