Uniden D3097 English Owner's Manual - Page 3

Getting Started - handset

Page 3 highlights

Getting Started Installing Your Phone Test the Connection Charge the Battery 1. Unpack all handsets, battery packs, and battery covers. If you need to remove a cover, press in on the notch and slide the cover down and off. 2. Line up the battery connector with the jack inside the handset; the connector only fits one way. 3. Push the connector in until it clicks into place; tug gently on the wires 1. Pick up the handset and press TALK/ FLASH. The handset sounds a dial tone, and the display shows Talk. -- If you don't hear a dial tone or the display says Check Tel Line, check the connection between the base and the phone jack. 2. Make a quick test call. (Press TALK/ FLASH to hang up.) -- If you keep hearing a dial tone, change to pulse dialing. -- If there's a lot of noise, check for interference (see page 22). 3. Test all handsets the same way. If you can't get a dial tone, move the handset closer to the base. to make sure the battery is securely Changing to Pulse Dialing connected. Your phone uses tone dialing by 4. Replace the battery cover and slide it default. If your phone company uses into place. pulse dialing, you need to change your 5. Use an AC adapter to connect the phone's dial mode. power jack on the base to a regular 1. Press MENU/OK and select Advanced indoor (120V AC) power outlet. Setup (see page 7 for using the Connect any chargers the same way. menus). 6. Place a handset in the base with the display facing forward. If the battery icon does not begin cycling through levels, reseat the handset or connect the base to a different outlet. For 2 or more handsets, place each handset in a charger. ##Charge all handsets completely (about 15 hours) before using. Connect the Telephone Cord Use the telephone cord to connect the TEL LINE jack on the base to a standard telephone wall jack. 2. Select Dial Mode then Pulse. You'll hear a confirmation tone. To send DTMF tones during a call (e.g., for an automated response system), press to temporarily switch to tone dialing. When you hang up, the phone automatically returns to pulse dialing. Attaching Optional Wall-Mount Bracket You can order a wall-mount bracket from the Uniden website. Follow the instructions that come with the bracket. English - 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

English - 3
Installing Your Phone
Charge the Battery
1. Unpack all handsets, battery packs,
and battery
covers. If you
need to
remove a
cover, press in
on the notch
and slide the
cover down
and off.
2. Line up the battery connector with
the jack inside the handset; the
connector only fits one way.
3. Push the connector in until it clicks
into place; tug gently on the wires
to make sure the battery is securely
connected.
4. Replace the battery cover and slide it
into place.
5. Use an AC adapter to connect the
power jack on the base to a regular
indoor (120V AC) power outlet.
Connect any chargers the same way.
6. Place a handset in the base with the
display facing forward. If the battery
icon does not begin cycling through
levels, reseat the handset or connect
the base to a different outlet. For
2 or more handsets, place each
handset in a charger.
#
Charge all handsets completely
(about 15 hours) before using.
Connect the Telephone Cord
Use the telephone cord to connect the
TEL LINE jack on the base to a standard
telephone wall jack.
Test the Connection
1. Pick up the handset and press
TALK/
FLASH
. The handset sounds a dial
tone, and the display shows
Talk
.
-
If you don't hear a dial tone or the
display says
Check Tel Line,
check
the connection between the base
and the phone jack.
2. Make a quick test call. (Press
TALK/
FLASH
to hang up.)
-
If you keep hearing a dial tone,
change to pulse dialing.
-
If there’s a lot of noise, check for
interference (see page 22).
3. Test all handsets the same way. If
you can't get a dial tone, move the
handset closer to the base.
Changing to Pulse Dialing
Your phone uses tone dialing by
default. If your phone company uses
pulse dialing, you need to change your
phone’s dial mode.
1. Press
MENU/OK
and select
Advanced
Setup
(see page 7 for using the
menus).
2. Select
Dial Mode
then
Pulse
. You’ll
hear a confirmation tone.
To send DTMF tones during a call (e.g.,
for an automated response system),
press
to temporarily switch to tone
dialing. When you hang up, the phone
automatically returns to pulse dialing.
Attaching Optional Wall-Mount
Bracket
You can order a wall-mount bracket
from the Uniden website. Follow the
instructions that come with the bracket.
GETTING STARTED