Uniden SC200 English Owners Manual - Page 35

Using CTCSS Tone or CDCSS Tone Search, While Searching

Get Uniden SC200 PDF manuals and user guides View all Uniden SC200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

5. Repeat Steps 1 - 4 to search for tones associated with other stored frequencies. If you want to program tones for several stored frequencies, follow these steps: n After you program a CTCSS tone or CDCSS tone with a stored frequency, the CTCSS Tone or CDCSS tone Search Mode is canceled. The CTCSS or CDCSS indicator remains on but does not flash. To activate the CTCSS Tone Search Mode or CDCSS Tone Search Mode again, press and hold until you hear two short beeps. If you decide to cancel the CTCSS Tone Search Mode or CDCSS Tone Search Mode while scanning, press and hold until you hear two short beeps and the CTCSS or CDCSS indicator turns off. n You can select the CTCSS Search Mode or CDCSS Tone Search Mode before pressing in Manual Mode. Simply, press and hold until the CTCSS or DCS indicator begins flashing, and then press . When your scanner stops, the CTCSS Tone or CDCSS Tone search begins immediately. If a tone is found before the transmission ends, press to program the tone with the frequency stored in the channel. Using CTCSS Tone or CDCSS Tone Search While Searching 1. Set a Search Range. For information about setting a search range, see Limit Search on page 27. 2. Press and hold until you hear two short beeps. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
5.
Repeat Steps 1 - 4 to search for tones associated with
other stored frequencies.
If you want to program tones for several stored
frequencies, follow these steps:
n
After you program a CTCSS tone or CDCSS
tone with a stored frequency, the CTCSS Tone
or CDCSS tone Search Mode is canceled. The
CTCSS or CDCSS indicator remains on but
does not flash. To activate the CTCSS Tone
Search Mode or CDCSS Tone Search Mode
again, press and hold
until you hear two
short beeps.
If you decide to cancel the CTCSS Tone Search
Mode or CDCSS Tone Search Mode while
scanning, press and hold
until you hear two
short beeps and the CTCSS or CDCSS indicator
turns off.
n
You can select the CTCSS Search Mode or
CDCSS Tone Search Mode before pressing
in Manual Mode. Simply, press and hold
until the CTCSS or DCS indicator begins
flashing, and then press
.
When your scanner stops, the CTCSS Tone or
CDCSS Tone search begins immediately. If a
tone is found before the transmission ends,
press
to program the tone with the
frequency stored in the channel.
Using CTCSS Tone or CDCSS Tone Search
While Searching
1.
Set a Search Range.
For information about setting a search range, see Limit
Search on page 27.
2.
Press and hold
until you hear two short beeps.
33