ViewSonic IFP9850 Gen 4 - 98" ViewBoard 4K Ultra HD Interactive Flat Panel IFP - Page 105

LAN Hardware Specification, RS232 Communication Setting, Command Message Reference

Get ViewSonic IFP9850 Gen 4 - 98inch ViewBoard 4K Ultra HD Interactive Flat Panel PDF manuals and user guides View all ViewSonic IFP9850 Gen 4 - 98" ViewBoard 4K Ultra HD Interactive Flat Panel manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

LAN Hardware Specification ViewSonic LFD communication port on the rear side: 1. Connector type: 8P8C RJ45 2. Pin Assignment: Pin # 1 2 3 4 5 6 7 8 frame Signal TX+ TXRX+ BI_D3+ BI_D3RXBI_D4+ BI_D4GND Remark Output from Display Output from Display Input to Display For 1G case For 1G case Input to Display For 1G case For 1G case RS232 Communication Setting - Baud Rate Select: - Data bits: - Parity: - Stop Bits: 9600bps (fixed) 8 bits (fixed) None (fixed) 1(fixed) LAN Communication Setting - Type: - Protocol: - Port: - Cross subnet: - Logon Credentials: Ethernet TCP/IP 5000 (fixed) No No Command Message Reference PC sends to LFD command packet followed by "CR". Every time PC sends control command to Display, the Display shall respond as follows: 1. If the message is received correctly it will send "+" (02Bh) followed by "CR" (00Dh) 2. If the message is received incorrectly it will send "-" (02Dh) followed by "CR" (00Dh) 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
105
LAN Hardware Specifica°on
ViewSonic LFD communica°on port on the rear side:
1.
Connector type: 8P8C RJ45
2.
Pin Assignment:
Pin #
Signal
Remark
1
TX+
Output from Display
2
TX-
Output from Display
3
RX+
Input to Display
4
BI_D3+
For 1G case
5
BI_D3-
For 1G case
6
RX-
Input to Display
7
BI_D4+
For 1G case
8
BI_D4-
For 1G case
frame
GND
RS232 Communica°on Se²ng
- Baud Rate Select:
9600bps (fixed)
- Data bits:
8 bits (fixed)
- Parity:
None (fixed)
- Stop Bits:
1(fixed)
LAN Communica°on Se²ng
- Type:
Ethernet
- Protocol:
TCP/IP
- Port:
5000 (fixed)
- Cross subnet:
No
- Logon Creden°als:
No
Command Message Reference
PC sends to LFD command packet followed by “CR”. Every °me PC sends control
command to Display, the Display shall respond as follows:
1.
If the message is received correctly it will send “+” (02Bh) followed by “CR”
(00Dh)
2.
If the message is received incorrectly it will send “-” (02Dh) followed by “CR”
(00Dh)