ViewSonic LS700HD User Guide
ViewSonic LS700HD Manual
 |
View all ViewSonic LS700HD manuals
Add to My Manuals
Save this manual to your list of manuals |
ViewSonic LS700HD manual content summary:
- ViewSonic LS700HD | User Guide - Page 1
LS700HD DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage - ViewSonic LS700HD | User Guide - Page 2
, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there - ViewSonic LS700HD | User Guide - Page 3
ventilation openings. Install the unit in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any - ViewSonic LS700HD | User Guide - Page 4
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to - ViewSonic LS700HD | User Guide - Page 5
Your Records" section. For additional information, please see the "Customer Support" section in this guide. Product Name: Model Number: Document Number: Serial Number: Purchase Date: For Your Records LS700HD ViewSonic DLP Projector VS17454 LS700HD_UG_ENG Rev.1A 04-17-19 Product disposal at end - ViewSonic LS700HD | User Guide - Page 6
37 Control the projector with the web browser 38 About Crestron e-Control 41 Using the projector under standby mode 43 Switch off the projector 44 Menu operations 45 Description of each menu 48 Maintenance 52 Care of the projector 52 LED Indicator 53 Troubleshooting 54 Specifications 55 - ViewSonic LS700HD | User Guide - Page 7
Fuse specifications 55 Dimensions 56 Ceiling mount installation 56 Timing chart 57 Copyright information..... 61 Copyright 61 Disclaimer 61 Appendix 62 IR control table 62 Address Code 63 RS232 command table 64 vi - ViewSonic LS700HD | User Guide - Page 8
user safety. Safety Instructions ●●Please read through this manual before using the projector. Save it for future reference. ●●Do not look straight at the projector lens during operation. The intense light beam may damage your eyes. ●●Refer servicing to qualified service personnel. ●●Always open - ViewSonic LS700HD | User Guide - Page 9
the market. Safety instructions for ceiling mounting of the projector We hope you to have a pleasant user experience with our projector. This is why projector as well as the base of the ceiling mounting support. This will provide additional protection in case the connectors of the mounting support - ViewSonic LS700HD | User Guide - Page 10
features: ●●The color mode provides different options designed for different projectors. ●●Compatible with NTSC, PAL, SECAM and HDTV ●●D-Sub 15-pin terminal can be connected to analog video ●●Equipped with HDMI connection, supports HDCP (PA501S with no such features) ●●Multi-language On-Screen - ViewSonic LS700HD | User Guide - Page 11
of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated. VGA cable Projector On Off COMP VIDEO HDMI Auto Sync Source Aspect Freeze Pattern Blank PgUp PgDn Color Mode Remote Control and Batteries Power cord - ViewSonic LS700HD | User Guide - Page 12
External appearance of the projector Front/Rear Side Top/Bottom Warning ●●This equipment must be grounded. ●●You may add power interruption devices in the fixed wiring or plug in the - ViewSonic LS700HD | User Guide - Page 13
): Selects the required menu item to make adjustments. : Adjusts the projector's sound level. 7. / Up/ Down (direction buttons): Selects the required menu item to make adjustments. / (Keystone button): Manually corrects distorted images resulting from an angled projection. 8. Source A source - ViewSonic LS700HD | User Guide - Page 14
the displayed image. 4. Keystone button and direction button /// Manually corrects distorted images resulting from an angled projection. Left/Right/Up/Down Selects the required menu item to make adjustments. 5. Displays the projector's internal information. 6. Menu Open the OSD menu. running - ViewSonic LS700HD | User Guide - Page 15
to display (OSD) menu item. 18. Exit Return to the previous OSD menu to exit and save the menu settings. 19. Pattern Shows the inbuilt testing screens. 20. Blank Hide screen image. 22. (Volume+) Increase the volume. 23. (Zoom in) The displayed zoom lever can be used to zoom in on - ViewSonic LS700HD | User Guide - Page 16
control code then switch the code of the remote control itself. If you want to switch the code at the projector end, please go to System: Remote Control Code menu and select 1 to 8. If you want to switch the code at the remote control end, On - ViewSonic LS700HD | User Guide - Page 17
control to replace your cursor, fix one end of the USB cable to the projector Mini USB port and the other end to the PC or notebook computer. See 26 feet). Do not place any obstruction in front of the IR sensor on the projector as this may block the IR beam. Approx. 30° 2 Note ●●When an intense - ViewSonic LS700HD | User Guide - Page 18
, sauna, solarium or car. ●●Replace only with the same or equivalent type recommended by the battery manufacturer. ●●Refer to the manufacturer's instructions and local environmental regulations to dispose of old batteries. ●●Do not throw batteries into fires. There may be danger of an explosion - ViewSonic LS700HD | User Guide - Page 19
is suspended upside-down from the ceiling in front of the screen. Purchase a Projector Ceiling Mounting Kit from your dealer to mount your projector on the ceiling. After turning on the projector, go to System: Projector Position menu and select Front Ceiling. 3. Rear Ceiling For this location, the - ViewSonic LS700HD | User Guide - Page 20
3% tolerance among these numbers due to optical component variations. It is recommended that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector before you permanently install it, so as to make allowance for this - ViewSonic LS700HD | User Guide - Page 21
for each source. 3. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included within the projector packaging (please refer to "Shipping contents"). You may purchase the required signal cables from an electronics store. The following links and icons are - ViewSonic LS700HD | User Guide - Page 22
end of the VGA cable to the COMPUTER signal input jack on the projector. Many notebooks have not activated their monitor jack after being connected to FN key and the labeled function key. Please refer to the instruction manual provided with the notebook computer for the combination keys and their - ViewSonic LS700HD | User Guide - Page 23
jacks, you will be able to acquire uncompressed digital video quality. Please refer to "Connecting to HDMI devices" for details on how to connect the projector to HDMI devices. If you don't have any usable HDMI source, the next best video signal would be Component Video (not to be confused with - ViewSonic LS700HD | User Guide - Page 24
projected picture displays wrong colors, please change the color space to YUV. See "Changing HDMI input settings" for details. To connect the projector to a Component Video source device: Examine your Video source device to determine if a set of unused Component Video output sockets are available - ViewSonic LS700HD | User Guide - Page 25
Audio playback with the projector You can use the speaker of the projector in the presentation or connect other individual speakers to the AUDIO OUT jack of the projector. 18 - ViewSonic LS700HD | User Guide - Page 26
. 3. If this is the first time that you've switched on the projector, please refer to on-screen instructions and select your OSD language. 4. Switch on all connected equipment. The projector will then begin a search of the input signals. The lower right corner of the screen will display the current - ViewSonic LS700HD | User Guide - Page 27
5. Press Menu and then press the 6. Press Menu and then press the remote control / to select the remote control / to select Image Display and press to select Aspect and press to select Color Mode. Ratio. 7. Press Menu and then press the 8. Press Menu and then press the remote - ViewSonic LS700HD | User Guide - Page 28
password. You may use the password recall procedure if you forgot your password and did not record it in this manual. See "Entering the password recall procedure" for details. If you enter an incorrect password 5 times in succession, the projector will automatically shut down for a short time. 21 - ViewSonic LS700HD | User Guide - Page 29
procedure 1. Press and hold the [Auto Sync] button on the remote control for 3 seconds. 2. Write down the number and turn off your projector. 3. Seek help from the local service center to decode the number. You may be required to provide proof of purchase to verify that you are an authorized user of - ViewSonic LS700HD | User Guide - Page 30
selection button on the remote control or search for available input signals to manually select the desired signals. 1. Press [Source] to display the source at this resolution. Any other resolutions will be scaled by the projector depending upon the aspect ratio setting, which may cause some image - ViewSonic LS700HD | User Guide - Page 31
range settings of the output device. ●● Enhanced: Changes HDMI color range to 0-255. ●● Normal: Changes HDMI color range to 16-235. ●● Auto: Sets the projector to automatically detect the HDMI range of the input signal. This function is only available when the HDMI input jack is being used. Please - ViewSonic LS700HD | User Guide - Page 32
angle along the vertical axis. The user may turn the adjustment support peg to make fine adjustments to projection angle and position of the projected image until it reaches the desired location. 1 2 Lift and adjust the feet If the projector is placed on an uneven surface or where the screen and - ViewSonic LS700HD | User Guide - Page 33
Keystone distortion is a problem where the projected image becomes trapezoidal in shape (keystone distortion) as a result of poor projection angle. To correct this situation, you should adjust projector height and use the following steps to correct the issue manually. ●● Using the remote - ViewSonic LS700HD | User Guide - Page 34
aspect ratio, while digital TV and DVDs have 16:9 aspect ratios. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio - ViewSonic LS700HD | User Guide - Page 35
About the aspect ratio Choose how to make the screen suitable for the screen: 1. Auto: projector's natural resolution in its horizontal width. This is suitable where the incoming image is neither in 4:3 nor 16:9 aspect ratios Image 16:10 but where - ViewSonic LS700HD | User Guide - Page 36
) environments to achieve the best viewing effects. 4. Brightest: Maximizes the brightness of the projected image. This mode is suitable when using projectors in environments such as well-lit rooms where extra-high brightness is required. 5. Sports mode: Tint suitable for watching sporting events - ViewSonic LS700HD | User Guide - Page 37
Fine-tuning of image quality in user modes You may use several user-defined functions if the projector detects certain signal types. You can make adjustments to these functions based on your needs. Adjusting Brightness Enter Image > Brightness menu and then press /. The - ViewSonic LS700HD | User Guide - Page 38
the projected image. Brightness levels of mid-tone areas commonly seen in videos and natural landscapes are increased by more than 50%, allowing the projector to generate images in realistic and true colors. To acquire this quality of images, please select the level you desire. If not required, set - ViewSonic LS700HD | User Guide - Page 39
allow for more accurate color reproduction, should you require it. If you have purchased a test disc that contains various color test patterns that can be used to test the color presentation of monitors, TVs, and projectors, any image from the disc can be projected on screen and adjusted using the - ViewSonic LS700HD | User Guide - Page 40
Setting the Presentation Timer The presentation timer can indicate the presentation time on-screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function: 1. Enter Basic > Presentation Timer menu. 2. Press [Enter] to show the Presentation - ViewSonic LS700HD | User Guide - Page 41
accidentally (by children, for example). Once Panel Key Lock has been activated, with the exception of the Power button, none of the buttons on the projector could be used. 1. Go to System > Panel Key Lock menu. 2. Press / and select ON. To switch off the Panel Key Lock, press and hold the - ViewSonic LS700HD | User Guide - Page 42
, press / to select Power Saving, or press [Eco Mode] on the remote control to make the choice. Setting Auto Power Off This function allows the projector to enter Sleep mode automatically after the set time, to avoid unnecessary wastage of the light source. 1. Open the OSD menu and go to the - ViewSonic LS700HD | User Guide - Page 43
HDMI and achieve synchronized power ON/OFF operations. This means that when a device that also supports CEC is connected to the HDMI input jack of the projector, switching off the power of the projector will also automatically switch off the power of the connected device. Switching on the power of - ViewSonic LS700HD | User Guide - Page 44
projector will look for a 3D Sync data signal. Once detected, the projector will automatically switch to 3D projection. Under other circumstances, you may need to manually ] to correct this problem. Control the projector through the local area network This projector supports Crestron® software. After - ViewSonic LS700HD | User Guide - Page 45
. If Microsoft Internet Explorer is used, make sure the version is 7.0 or higher. The screenshots in this manual are for reference only. Actual OSD design may differ. 1. Enter the address of the projector in the address bar of your browser and press [Enter]. 2. The homepage of "Network Control" is - ViewSonic LS700HD | User Guide - Page 46
is selected. For details of the AMX Device Discovery, please access the AMX website: http://www.amx.com/. 4. If the projector is connected to the network which supports the SMTP (Simple Mail Transfer Protocol), you can configure it to send alarms via emails when important events occur. 5. Crestron - ViewSonic LS700HD | User Guide - Page 47
Password SNMP Email Setting Email Alert SMTP Setting Alert Condition Input length Maximum character DHCP/Manual (None) IP Address XXX.XXX.XXX.XXX Subnet Mask XXX.XXX.XXX.XXX Gateway (None) Light source Time Alert (None) Submit (None) Issue Test Mail (None) are forbidden. 40 - ViewSonic LS700HD | User Guide - Page 48
settings, and perform remote network operation security access to the projector. i ii iv iii v vi i. This part can be used only in the case that the Crestron control system is used. Please contact Creston or refer to its user guide to get a knowledge of the installation information. ii. You - ViewSonic LS700HD | User Guide - Page 49
, please input the English letters and digits in the Tools page. After adjustment, press the Send button and the data will be saved in the projector. vi. Press Exit and then you can return to the remote network operation page. Please note the input length limits in the following table (including - ViewSonic LS700HD | User Guide - Page 50
access the following website to obtain the RoomView™ User Guide and more information: http://www.crestron.com/products/roomview_connected_embedded_projectors_ devices/resources.asp Support PJLink™, SNMP, AMX and Xpanel formats This projector is compatible with PJLink™, SNMP V.1, AMX or Xpanel V1 - ViewSonic LS700HD | User Guide - Page 51
message will be displayed on screen. The message will disappear if you do not respond within a few seconds. 2. Press the Power Button again, and the projector will be turned off. Wait until the fan is completely stopped and unplug the power cord. 3. Disconnect the power cord from the wall socket if - ViewSonic LS700HD | User Guide - Page 52
must detect at least one valid signal in order to use the menu items. If no device has been connected to the projector or if no signal has been detected, only a few menu items will be accessible. Main menu Sub-menu Aspect Ratio Keystone 1. Display 2. Image Corner Adj. - ViewSonic LS700HD | User Guide - Page 53
-Right Count down/count up Sound reminder Off/On Start Counting Yes/No Pattern Off/Test Card Blank Timer Disable/5 min/10 min/15 min/20 min/25 min/30 min Message On/Off Splash Screen Blue/ViewSonic/Off 3D Settings 3D Sync Save 3D Settings Off/Frame sequence/Frame Packing/Top - ViewSonic LS700HD | User Guide - Page 54
7. Information Sub-menu Light source setting Light Source Mode Light Source Power Light Source Hours Closed Caption Reset settings Language Projector Position Closed Caption Enable Caption Version Menu Settings Menu Display Time Menu Position High Altitude Mode Quick Auto Search Security - ViewSonic LS700HD | User Guide - Page 55
Description of each menu Function Aspect Ratio Keystone Corner Adj. Position Description See "Selecting the aspect ratio" for details. See "Perform keystone correction" for details. See "Adjust four corners" for deatils. Displays the position adjustment page. To move the projected image, use the - ViewSonic LS700HD | User Guide - Page 56
See "Color Management" for details. Returns all color settings to the factory preset values. Signal Set whether or not to automatically turn on when the projector is in the standby mode or the VGA or HDMI signal of 5V power is detected. CEC See "Using the CEC function" for details. Direct - ViewSonic LS700HD | User Guide - Page 57
Reset Settings Mute Description Volume Power On/Off Ring Tone When turning on or off the projector, it will make a sound. See "Setting the Presentation Timer" for details. The projector can display a test pattern. It helps you adjust the image size and focus and check that the projected image - ViewSonic LS700HD | User Guide - Page 58
6. System menu Function Language Projector Position Menu Settings High Altitude Mode Quick Auto Search Security input system format. IP Address Displays the IP address of the projector. MAC Address Displays the MAC address of the projector. Firmware Version 3X Fast Input 7. Information menu 51 - ViewSonic LS700HD | User Guide - Page 59
. These can damage the case. Storing the projector Follow the instructions below to store the projector for an extended time: ●●Make sure the for the projector. Please refer to "Specifications" or inquire your dealer for details of the recommended range. ●●Retract the projector support pegs. - ViewSonic LS700HD | User Guide - Page 60
LED Indicator Projector status Stand-by mode Normally on Normal Operations Temperature Error 1 Temperature Error 2 Fan Error 1 Fan Error 2 Fan Error 3 or 4 Color Wheel Error Light bulb abnormal - ViewSonic LS700HD | User Guide - Page 61
Troubleshooting Projector is not shutting down Cause There is no power from the power cable. Attempting to turn the projector on again during the cooling process. Remedy Plug one end of the power cable at the AC inlet of the projector and the other end in the power outlet. If the power outlet has - ViewSonic LS700HD | User Guide - Page 62
specifications ●● All specifications are subject to change without notice. ●● Not all projector models are available at your location. Input Terminals 1 VGA input (DB 15 pin) x2 2 HDMI (v1.4 with audio ) x2 3 Video (RCA) x1 4 Audio input (3.5mm - ViewSonic LS700HD | User Guide - Page 63
Dimensions 396.0mm 156.8mm 313.8mm Ceiling mount installation 265.0mm 34.0mm 30.0mm 135.0mm 15.0mm Note: It is recommended to use the M4L8 screw for fixing the projector using the M4 screw hole. (M4/ L8 x 4) 56 - ViewSonic LS700HD | User Guide - Page 64
Timing chart Signal VGA SVGA XGA WXGA Quad-VGA SXGA SXGA+ WXGA+ UXGA WSXGA+ HD MAC 13" MAC 16" MAC 19" MAC 21" HDTV (1080p) Analog RGB Resolution (pixels) Aspect Ratio 640x480 4:3 800x600 4:3 1024x768 4:3 1152x864 4:3 1280x768 15:9 1280x800 16:10 1360x768 16:9 1366x768 16:9 - ViewSonic LS700HD | User Guide - Page 65
Signal VGA SVGA XGA WXGA Quad-VGA SXGA SXGA+ WXGA+ WSXGA+ HDTV (1080p) HDTV (1080i) HDTV (720p) SDTV(480p) SDTV(576p) SDTV (480i) SDTV (576i) HDMI Resolution (pixels) Aspect Ratio 640x480 4:3 800x600 4:3 1024x768 4:3 1280x768 15:9 1280x800 16:10 1360x768 16:9 1366x768 16:9 1280x960 - ViewSonic LS700HD | User Guide - Page 66
rate (Hz) SDTV (480i)** 720x480 4:3/16:9 60 * 50 Hz and 60 Hz signals are supported for side by side, Top and Bottom, and Frame Sequential formats. ** The video signal (SDTV 480i) supports only the frame Sequential format. HDMI 3D Within frame packing formats Signal Resolution (pixels - ViewSonic LS700HD | User Guide - Page 67
Signal HDTV (1080p) HDTV (1080i) HDTV (720p) SDTV(480p) SDTV(576p) SDTV (480i) SDTV (576i) Component video Resolution (pixels) Aspect Ratio 1920x1080 16:9 1920x1080 16:9 1280x720 16:9 720x480 4:3/16:9 720x576 4:3/16:9 720x480 4:3/16:9 720x576 4:3/16:9 Refresh rate (Hz) 50/60 50/60 - ViewSonic LS700HD | User Guide - Page 68
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic. Disclaimer ViewSonic does not make any statement or warranty, expressed or implied, for the merchantability and fitness for - ViewSonic LS700HD | User Guide - Page 69
Appendix IR control table Button PgDn PgUp Blank Auto Sync Up Down Left Right Color Mode Mute Input Powering up Power Off Exit Eco mode Menu Source Pattern Video HDMI Volume+ VolumeZoom+ ZoomFreeze Aspect COMP Information Format NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC - ViewSonic LS700HD | User Guide - Page 70
Address Code Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 83F4 93F4 A3F4 B3F4 C3F4 D3F4 E3F4 F3F4 RS232 command table Pin Description Pin 1 NC 2 3 TX 4 5 GND 6 7 RTSZ 8 9 NC Description RX NC NC CTSZ Baud Rate Data - ViewSonic LS700HD | User Guide - Page 71
Power Write ON 2 Power Write OFF 3 Power Read Status 4 Projector Read Status Status (Note 7) 5 Reset All Write Reset All Settings Color Settings Settings 7 Splash Screen Write Blue 8 Splash Screen Write ViewSonic 9 Splash Screen Write OFF 10 Splash Screen Read Status 11 High - ViewSonic LS700HD | User Guide - Page 72
0x14 0x00 0x03 0x00 0x00 0x00 0x00 Position 0x00 0x00 0x5E 0x17 26 Projector Position Write Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x14 0x00 0x03 0x00 0x00 0x00 0x02 Position 0x00 0x02 0x60 0x19 28 Projector Write Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x14 0x00 - ViewSonic LS700HD | User Guide - Page 73
No. Function Type Action Command Response The response of Query Read command 55 Horizontal Write Shift Left position 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x14 0x00 0x00 0x00 0x14 0x06 0x00 0x64 56 Horizontal Read Get Value position 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x05 0x14 0x00 0x03 - ViewSonic LS700HD | User Guide - Page 74
No. Function Type Action Command Response The response of Query Read command 85 Primary Color 86 Primary Color 87 Hue / Tint Write Y Read Status Write Decrease 88 Hue / Tint Write Increase 89 Hue / Tint Read Get value 90 Saturation Write Decrease 91 Saturation Write Increase 92 Saturation - ViewSonic LS700HD | User Guide - Page 75
No. Function 115 Volume 116 Volume 117 Volume 118 Volume 119 Language 120 Language 121 Language 122 Language 123 Language 124 Language 125 Language 126 Language 127 Language 128 Language 129 Language 130 Language 131 Language 132 Language 133 Language 134 Language 135 Language 136 Language 137 - ViewSonic LS700HD | User Guide - Page 76
No. Function 145 HDMI Format 146 HDMI Range 147 HDMI Range 148 HDMI Range 149 HDMI Range 150 CEC Type Action Read Status Write Enhanced Write Normal Write Auto Read Status Write OFF 151 CEC Write ON 152 CEC Read Status Error status Read Status 153 154 Brilliant Color 155 Brilliant Color 156 - ViewSonic LS700HD | User Guide - Page 77
0x04 0x08 0x5A 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x03 0x14 0x00 0x00 0x00 0x14 0x04 0x11 0x63 AMX AMXB 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x05 0x14 0x00 0x0A 0x00 0x00 See note 1 0x00 0x15 0x03 0x65 0x00 0x29 0x01 0x00 - ViewSonic LS700HD | User Guide - Page 78
service debug) : Response : 0x05 0x14 0x00 0x16 0x00 0x00 0x00 ErrorStatus(20 Items) checksum 1． Item 0 ~17: 1 byte. 2． Item 18 : First burn In error minutes， 4 Bytes. 3． Item 19: Lamp Status，1 Byte. 4． Item 20: Lamp error status，2 Bytes. Total : 32 Bytes 。 3. When the projector to User Guide. 6. The - ViewSonic LS700HD | User Guide - Page 79
http://www.viewsoniceurope.com/eu/support/call-desk/ Hong Kong www.hk.viewsonic.com T= 852 3102 2900 [email protected] India www.in.viewsonic.com T= 1800 419 0959 [email protected] Korea ap.viewsonic.com/kr/ T= 080 333 2131 [email protected] Latin America (Argentina - ViewSonic LS700HD | User Guide - Page 80
ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic instructions supplied - ViewSonic LS700HD | User Guide - Page 81
, contact ViewSonic Customer Support (please refer to "Customer Support" page). You will need to provide your product's serial number. 2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem - ViewSonic LS700HD | User Guide - Page 82
modification, unauthorized attempted repair, or failure to follow instructions supplied with the product. b. A ny damage service charges. How to get service: For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support - ViewSonic LS700HD | User Guide - Page 83
39300 Acapulco, Guerrero Tel: 744-48-32627 Monterrey: Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. SUPPORT: ViewSonic Corporation 14035 Pipeline Ave. Chino, CA 91710, USA Tel: 800-688-6688 (English); 866-323-8056 (Spanish); E-Mail: http://www.viewsonic.com Projector - ViewSonic LS700HD | User Guide - Page 84
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
 |
 |
LS700HD
DLP Projector
User Guide
Model No. VS17454
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service.
Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specific languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”