ViewSonic PF790 User Manual - Page 12

Troubleshooting

Page 12 highlights

Troubleshooting No power • Press Power button ON. • Make sure A/C power cord is securely connected to back of monitor and to a power outlet. E • Plug another electrical device (like a radio) into power outlet to verify that outlet is supplying proper voltage. Power on but no screen image • Make sure video cable supplied with monitor is tightly secured to video output port on back of computer. If other end of video cable is not attached permanently to monitor, tightly secure it to monitor. • Adjust the brightness and contrast. • Check this user's guide to see if an adapter is required for proper signal continuity between graphics card and monitor. Flickering • Not enough power supplied. Connect monitor to different outlet. If using surge protector, reduce number of devices plugged in. • Check ViewMeter°to verify refresh rate (vertical frequency) is 75 Hz or higher. See the "Specifications" section. • Make sure graphics card in your computer can use non-interlaced mode at desired frequencies. To enable your graphics card to support higher refresh rates, try selecting fewer colors or running lower resolutions. • Remove any devices from area around monitor that emit magnetic fields such as radios, surge protectors, unshielded speakers, fluorescent lights, AC power converters, desk fans, etc. Wrong or abnormal colors • If any colors (red, green, or blue) are missing, check video cable to make sure it is securely connected. Loose pins in the cable connector could cause a bad connection. • Connect monitor to another computer. • Turn monitor OFF, wait one minute, then turn ON again. Do this only once. • If you have an older graphics card, contact customer support for a non-DDC adapter. Entire screen image scrolls (rolls) vertically • Make sure video input signals are within monitor's specified frequency range. • Try monitor with another power source, graphics card, or computer system. • Connect video cable securely. Control buttons do not work • Press only one button at a time. ViewSonic PF790 Other Information 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18

Troubleshooting
No
power
Press
Power
button
ON.
Make
sure
A/C
power
cord
is
securely
connected
to
back
of
monitor
and
to
a
power
outlet.
E
Plug
another
electrical
device
(l
ike
a
radio)
into
power
outlet
to
verify
that
outlet
is
supplying
proper
voltage.
Power
on
but
no
screen
image
Make
sure
video
cable
supplied
with
monitor
is
tightly
secured
to
video
output
port
on
back
of
computer.
If
other
end
of
video
cable
is
not
attached
permanently
to
monitor,
tightly
secure
it
to
monitor.
Adjust
the
brightness
and
contrast.
Check
this
user's
guide
to
see
if
an
adapter
is
required
for
proper
signal
continuity
between
graphics
card
and
monitor.
Flickering
Not
enough
power
suppl
ied.
Connect
monitor
to
different
outlet.
If
using
surge
protector,
reduce
number
of
devices
plugged
in.
Check
ViewMeter°to
verify
refresh
rate
(vertical
frequency)
is
75
Hz
or
higher.
See
the
"Specifications"
section.
Make
sure
graphics
card
in
your
computer
can
use
non
-interlaced
mode
at
desired
frequencies.
To
enable
your
graphics
card
to
support
higher
refresh
rates,
try
selecting
fewer
colors
or
running
lower
resolutions.
Remove
any
devices
from
area
around
monitor
that
emit
magnetic
fields
such
as
radios,
surge
protectors,
unshielded
speakers,
fluorescent
lights,
AC
power
converters,
desk
fans,
etc.
Wrong
or
abnormal
colors
If
any
colors
(red,
green,
or
blue)
are
missing,
check
video
cable
to
make
sure
it is
securely
connected.
Loose
pins
in
the
cable
connector
could
cause
a
bad
connection.
Connect
monitor
to
another
computer.
Turn
monitor
OFF,
wait
one
minute,
then
turn
ON
again.
Do
this
only
once.
If
you
have
an
older
graphics
card,
contact
customer
support
for
a
non-DDC
adapter.
Entire
screen
image
scrolls
(rolls)
vertically
Make
sure
video
input
signals
are
within
monitor's
specified
frequency
range.
Try
monitor
with
another
power
source,
graphics
card,
or
computer
system.
Connect
video
cable
securely.
Control
buttons
do
not
work
Press
only
one
button
at
a
time.
ViewSonic
PF790
Other
Information
11