ViewSonic PJ510 User Guide - Page 27

PICTURE-1 Menu Continued, PICTURE-2 Menu

Get ViewSonic PJ510 - SVGA LCD Projector PDF manuals and user guides
UPC - 766907013412
View all ViewSonic PJ510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

PICTURE-1 Menu (Continued) Item Description MY MEMORY Load/Save a Setting: Selecting one from the following and then pressing the (X) or the ENTER button performs each function. LOAD1(S)Q(T)LOAD2(S)Q(T)LOAD3(S)Q(T)LOAD4(S) (T)SAVE1(S)Q(T)SAVE2(S)Q(T)SAVE3(S)Q(T) SAVE4 • This projector has 4 memories called M1, M2, M3 and M4 for settings. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current setting data on the memory whose number corresponds. Performing the LOAD1, LOAD2, LOAD3 or LOAD4 calls the data of memory whose number corresponds, and adjusts the picture automatically depending on the data. • The LOAD1, LOAD2, LOAD3 or LOAD4 cannot be selected cannot be selected when there is no memory whose number corresponds. • At a different signal input from the signal that was being inputted when the setting was memorized, the picture may not be adjusted correctly. RESET Reset the PICTURE-1 Menu Items: Selecting the EXECUTE performs this function. EXECUTE (S)  CANCEL • The items of the PICTURE-1 menu are collectively returned to the initial setting. Note that the items MY MEMORY and CUSTOM-GAMMA are not reset. PICTURE-2 Menu With the PICTURE-2 menu, the items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description V POSITION H POSITION H PHASE Adjust the Vertical Position: Up (S) Q (T) Down • This item can be selected only at a RGB input Adjust the Horizontal Position: Left (S) Q (T) Right • This item can be selected only at a RGB input Adjust the Horizontal Phase (to eliminate flicker): Right (S) Q (T) Left • This item can be selected only at a RGB input or a COMPONENT VIDEO input. H SIZE Adjust the Horizontal Size: Large (S) Q (T) Small • When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please press the RESET button during selection of this item to reset the H SIZE. • This item can be selected only at a RGB input OVER SCAN RESET Adjust the Over-scan Ratio: Large (S) Q (T) Small • This item can be selected only at a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input • When this adjustment is too large, a certain degradation may appear at the frame area of the picture. In such a case, please adjust small. Reset the PICTURE-2 Menu Items: Selecting the EXECUTE performs this function. EXECUTE (S)  CANCEL • The items of the PICTURE-2 menu are collectively returned to the initial setting. Note that the H PHASE item is not reset. ViewSonic PJ510 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
ViewSonic
PJ510
24
PICTURE-1 Menu (Continued)
PICTURE-2 Menu
With the PICTURE-2 menu, the items shown in the Table below can be
performed. Perform each operation in accordance with the instructions in the
table below.
Item
Description
MY MEMORY
Load/Save a Setting:
Selecting one from the following and then pressing the (
) or the ENTER button performs each
function.
LOAD1(
)
(
)LOAD2(
)
(
)LOAD3(
)
(
)LOAD4(
)
(
)SAVE1(
)
(
)SAVE2(
)
(
)SAVE3(
)
(
) SAVE4
•
This projector has 4 memories called M1, M2, M3 and M4 for settings. Performing the SAVE1,
SAVE2, SAVE3 or SAVE4 puts the current setting data on the memory whose number
corresponds. Performing the LOAD1, LOAD2, LOAD3 or LOAD4 calls the data of memory whose
number corresponds, and adjusts the picture automatically depending on the data.
•
The LOAD1, LOAD2, LOAD3 or LOAD4 cannot be selected cannot be selected when there is no
memory whose number corresponds.
•
At a different signal input from the signal that was being inputted when the setting was
memorized, the picture may not be adjusted correctly.
RESET
Reset the PICTURE-1 Menu Items:
Selecting the EXECUTE performs this function.
EXECUTE (
)
CANCEL
•
The items of the PICTURE-1 menu are collectively returned to the initial setting. Note that the
items MY MEMORY and CUSTOM-GAMMA are not reset.
Item
Description
V POSITION
Adjust the Vertical Position:
Up (
)
(
) Down
•
This item can be selected only at a RGB input
H POSITION
Adjust the Horizontal Position:
Left (
)
(
) Right
•
This item can be selected only at a RGB input
H PHASE
Adjust the Horizontal Phase (to eliminate flicker):
Right (
)
(
) Left
•
This item can be selected only at a RGB input or a COMPONENT VIDEO input.
H SIZE
Adjust the Horizontal Size:
Large (
)
(
) Small
•
When this adjustment is excessive, the picture may not be displayed correctly. In such a case,
please press the RESET button during selection of this item to reset the H SIZE.
•
This item can be selected only at a RGB input
OVER SCAN
Adjust the Over-scan Ratio:
Large (
)
(
) Small
•
This item can be selected only at a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO
input
•
When this adjustment is too large, a certain degradation may appear at the frame area of the
picture. In such a case, please adjust small.
RESET
Reset the PICTURE-2 Menu Items:
Selecting the EXECUTE performs this function.
EXECUTE (
)
CANCEL
•
The items of the PICTURE-2 menu are collectively returned to the initial setting. Note that the H
PHASE item is not reset.