Home » ViewSonic Manuals » Projectors » ViewSonic PJD6211P » Manual Viewer

ViewSonic PJD6211P PJD6211P User Guide (English) - Page 16

Installation

Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Installation Connecting the Projector 1 2 3 4 2 5 6 7 1 1 1 Audio Cable 2 VGA Cable (D-Sub to D-Sub) 3 RS-232 Cable 4 USB Cable 5 S-Video Cable 6 Composite Video Cable 7 VGA (D-Sub) to HDTV (RCA) Cable „ The figure above is a sample connection. This does not mean that all of these devices can or must be connected simultaneously. „ The cables that come with the projector may differ from the above illustration. The included cables are based on actual shipment delivery. ViewSonic PJD6211P 14

Section	Page
PJD6211P_UG_ENG.pdf	7
Projector Features	7
Package Contents	8
Projector with Lens Cap	8
AC Power Cord	8
VGA Cable (D-SUB to D-SUB)	8
Projector Overview	9
Using the Product	11
Control Panel	11
Connection Ports	12
Remote Control	13
Replacing the Battery	14
1. Push the catch to the left and remove the battery holder.	14
2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.	14
3. Push the battery holder back into the remote control until you feel a click.	14
Remote Control Operation	15
Installation	16
Connecting the Projector	16
Powering On/Off the Projector	17
Powering On the Projector:	17
1. Remove the projector lens cap.	17
2. Complete the AC power cord and peripheral signal cable(s) connections.	17
3. Press button to turn on the projector. The projector takes a minute or so to warm up.	17
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.	17
Powering Off the Projector:	17
1. Press button to turn off the projector lamp. You will see a message \	17
2. Press button again to confirm.	17
3. Disconnect the AC power cord from the electrical outlet and the projector.	17
4. Do not turn on the projector right after power off.	17
Adjusting the Projector	18
Adjusting the Projector Height	18
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.	18
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.	18
Adjusting the Projector Zoom and Focus	18
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.	18
2. Adjust the image by sliding the zoom ring.	18
Adjusting Projection Image Size	19
Menu Operation	20
1. Press the MENU button to open the OSD menu.	22
2. When OSD is displayed, use p / q to select any feature in the main menu.	22
3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.	22
4. Use p / q to select the desired item and adjust the settings with t / u.	22
5. Press the MENU button, the screen will return to the main menu.	22
6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.	22
Maintenance	26
Cleaning the Lens	26
Cleaning the Projector Housing	26
Cleaning the Filter Cover	26
1. Switch the projector off and unplug the AC power cord from the wall socket.	26
2. Remove the filter cover as the illustration shown.	26
3. Clean the filter cover.	26
4. Replace the filter cover.	26
5. Attach the filter cover.	26
6. Plug the power back into the projector.	26
Replacing the Lamp	27
1. Turn off the projector.	28
2. If the projector is installed in a ceiling mount, remove it	28
3. Unplug the power cord.	28
4. Loosen the screw in the side of the lamp cover and remove the cover.	28
5. Remove the screws from the lamp module, raise the handle, and lift out the module.	28
6. Insert the new lamp module into the projector and tighten the screws.	28
7. Replace the lamp cover and tighten the screw.	28
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.	28
9. Reset the lamp hour. Refer to the “Setting” menu.	28
Specifications	29
Appendix	30
LED Indicator Messages	30
Compatibility Modes	31
Computer:	31
Video:	32
Troubleshooting	33
Start-up problems	33
Image problems	33
RS-232 Command and Configuration	34