ViewSonic VPC100 User Guide - Page 37

Deleting the Supervisor Password

Get ViewSonic VPC100 - 1 GB RAM PDF manuals and user guides
UPC - 766907349627
View all ViewSonic VPC100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

BIOS Setup Utility User Password To set or change the user password: 1. Select Change User Password. 2. Type the password, then press [Enter]. The password can be an alphanumeric character of up to 6 characters in length. 3. Re-type the password to confirm, then press [Enter]. The Access level defined by the Supervisor determines the users' setup utility access. Password Check When a Supervisor or User password has been set, the Password Check option will be available in the Security Menu. With this option, you can configure when the system will prompt you for the password: • Setup: You are required to enter the password every time you access the BIOS Setup Utility. • Always: You are required to enter the password on every system boot. Clear the Password • Deleting the Supervisor Password 1. Select Change Supervisor Password. 2. When prompted to enter the new password, just press [Enter]. 3. A message will appear to confirm password is uninstalled. Press [Enter]. • Deleting the User Password 1. Select Clear User Password. 2. A message will appear to confirm clearing of password, select Ok then press [Enter]. NOTE Once you have set the Supervisor Password, you cannot start your computer without entering the password. Be sure not to forget the password. Write down your password and keep it safe and private from other people. ViewSonic VPC100 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
ViewSonic
VPC100
26
BIOS Setup Utility
User Password
To set or change the user password:
Select
Change User Password
.
Type the password, then press [Enter]. The password can be an
alphanumeric character of up to 6 characters in length.
Re-type the password to confirm, then press [Enter].
The Access level defined by the Supervisor determines the users’ setup utility
access.
Password Check
When a Supervisor or User password has been set, the
Password Check
option
will be available in the Security Menu.
With this option, you can configure when the
system will prompt you for the password:
Setup:
You are required to enter the password every time you access the
BIOS Setup Utility.
Always:
You are required to enter the password on every system boot.
Clear the Password
Deleting the Supervisor Password
Select
Change Supervisor Password
.
When prompted to enter the new password, just press [Enter].
A message will appear to confirm password is uninstalled. Press [Enter].
Deleting the User Password
Select
Clear User Password
.
A message will appear to confirm clearing of password, select
Ok
then press
[Enter].
NOTE
Once you have set the Supervisor Password, you cannot start your computer
without entering the password. Be sure not to forget the password. Write down your
password and keep it safe and private from other people.
1.
2.
3.
•
•
•
1.
2.
3.
•
1.
2.