ViewSonic X100-4K User Guide - Page 73

Controlling the Projector through a LAN Environment, Control, Wired LAN Control, Standby, LAN Control

Get ViewSonic X100-4K PDF manuals and user guides View all ViewSonic X100-4K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Controlling the Projector through a LAN Environment The projector supports Crestron® software. With the correct settings in the LAN Control Settings menu, you can manage the projector from a computer using a web browser when the computer and projector are properly connected to the same local area network. VGA IN YPbPr RJ45 LAN HDMI RS-232 RJ45 LAN CONTROL Configuring the LAN Control Settings If you are in an Automatic IP environment: 1. Take a RJ45 cable and connect one end to the RJ45 Control port of the projector, and the other end to your network. 2. Go to: Setting > Network Settings > Wired LAN Control. 3. Select Configure IP and ensure it is set to Automatic. 4. Wait for 15-20 seconds, then re-enter LAN Settings. Now, the projector's IP Address, Subnet Mask, Default Gateway, and DNS Server settings will be displayed. 5. Make note of the IP Address displayed in the Projector IP Address row. NOTE: • If the Projector IP Address still does not appear, contact your network administrator. • If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server will display 0.0.0.0. Ensure the cables are properly connected and try the above steps again. • If you need to connect to the projector in its Standby Mode, set Standby LAN Control to On in the Network Settings menu. 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
73
Controlling the Projector through a LAN Environment
The projector supports Crestron® soſtware. With the correct seµngs in the LAN
Control Seµngs menu, you can manage the projector from a computer using a web
browser when the computer and projector are properly connected to the same
local area network.
CONTROL
N
A
L
Configuring the LAN Control Se²ngs
If you are in an
Automa°c
IP environment:
1.
Take a RJ45 cable and connect one end to the RJ45
Control
port of the projector,
and the other end to your network.
2.
Go to:
Se²ng
>
Network Se²ngs
>
Wired LAN Control
.
3.
Select
Configure IP
and ensure it is set to
Automa°c
.
4.
Wait for 15-20 seconds, then re-enter
LAN Se²ngs
. Now, the projector’s
IP Address, Subnet Mask, Default Gateway, and DNS Server seµngs will be
displayed.
5.
Make note of the IP Address displayed in the Projector IP Address row.
NOTE:
•
If the Projector IP Address s°ll does not appear, contact your network
administrator.
• If the RJ45 cables are not properly connected, the Projector IP Address,
Subnet Mask, Default Gateway, and DNS Server will display 0.0.0.0. Ensure
the cables are properly connected and try the above steps again.
• If you need to connect to the projector in its Standby Mode, set
Standby
LAN Control
to
On
in the
Network Se²ngs
menu.