Viking DFUW1541CR Installation Instructions - Page 8
Electrical Connection
View all Viking DFUW1541CR manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
ELECTRICAL CONNECTION WARNING ELECTRICAL SHOCK HAZARD Failure to follow these instructions could result in fire or electrical shock. Electrical Requirements A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A time delay fuse or circuit breaker is recommended.) It is recommended that a separate circuit, serving only this appliance, be provided. Grounding type wall receptacle •ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE. •DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER SUPPLY CORD GROUND PLUG. •DO NOT USE AN EXTENSION CORD. Power Supply with 3-prong grounding plug Recommended Grounding Methods For your personal safety, this refrigeration product must be grounded. This appliance is equipped with a 5' power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong grounding type wall receptacle grounded in accordance with the National Electrical Code and local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local codes and ordinances. The third ground plug SHOULD NOT, under any circumstances, be cut or removed. All UL listed refrigerated products are equipped with this type of plug. FINAL PREPARATION 1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the wine cellar should be washed thoroughly with hot, soapy water, rinsed and wiped dry to remove film residue and any installation dust or debris before being used. Solutions stronger than soap and water are rarely needed. 2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive cloths, cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel; scratches are almost impossible to remove. LIGHT ASSEMBLY REPLACEMENT - 15" W. Models DANGER ELECTRICAL SHOCK HAZARD Failure to to disconnect the power cord when changing the light tube, could result in fire or electrical shock. Green ground wire Light assembly NOTE: Please contact your local Viking Range Corporation parts distributor or dealer to order a new light assembly. Hex head screw To replace the light, first disconnect the unit's power cord. Next, remove both the green ground wire screw located on the left of the light assembly and Plug Hex head screw the other screw located on the right of the light assembly with a 5-16" hex head screwdriver. (See drawing). Unplug the light unit and remove complete light assembly. To install the new light assembly, screw in the green ground wire screw and the screw located on the right with a 5/16" hex head screwdriver and plug the light unit in. 14 LIGHT TUBE REPLACEMENT - 24" W. Single Zone Models DANGER ELECTRICAL SHOCK HAZARD Failure to to disconnect the power cord when changing the light tube, could result in fire or electrical shock. NOTE: Please contact your Viking Range Corporation parts distributor or dealer to order new light tubes. Use only approved replacement light tubes from your dealer or manufacturer. This product uses two 6-watt light tubes to illuminate the interior of the wine cellar. The light tubes are very reliable electrical components, but should either or both light tubes not function properly, please call your local dealer for replacement light tubes. To replace the light tube: •Use a small Phillips head screwdriver to remove the two screws holding the cover plate over the back section of the light tube. Set the screws and cover plate aside for re-assembly later. •Using a small flat-blade screwdriver, gently lever the front section of the light tube down to allow it to be pulled clear of the light Light tube housing. Disconnect the two insulated electrical connectors from Connectors the cabinet's electrical cable and discard the old light tube. •Reconnect the insulated electrical connector of the new light tube Cover plate to the cabinet's electrical cable connectors. Make sure they are secure and fully inserted. Screws •Carefully realign the light tube's electrical terminals back into the rear of the light enclosure channel making sure not to crimp them. Gently insert the light tube along the length of the light enclosure channel. Press the light tube gently into the light enclosure channel. Only a small part of the light tube should project below the ceiling of the unit. DO NOT USE A HAMMER TO FIT THE LIGHT TUBE. •Place the light tube terminal cover plate back in its original position on the light enclosure's flange. Re-use the original two screws to secure the cover in place. Plug the unit into the electrical socket. Check to see if the light tubes operate properly. LIGHT TUBE REPLACEMENT - 24" W. Dual Zone Models DANGER ELECTRICAL SHOCK HAZARD Failure to to disconnect the power cord when changing the light tube, could result in fire or electrical shock. NOTE: Please contact your Viking Range Corporation parts distributor or dealer to order new light tubes. Use only approved replacement light tubes from your dealer or manufacturer. This product uses two light tubes to illuminate the interior of the wine cellar. There is one light tube located behind the control housing in the the upper compartment and one light tube attached to the underside of the cabinet divider in the lower compartment. Use replacement instructions and drawing from the 15"W. Models for this Dual Zone product. 15