Viking RVDD336R Installation Instructions - Page 6

Prepare The Downdraft, Cut Countertop Opening

Get Viking RVDD336R PDF manuals and user guides View all Viking RVDD336R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

VIKING RANGE, LLC Downdraft Ventilators PREPARE THE DOWNDRAFT Exterior Blower Installation The downdraft is shipped without a blower. Purchase a Model VEDV900 Exterior Blower and mount the 10" discharge plate to the downdraft as follows: 1. Place the downdraft on its back on a table of flat work surface. 2. Remove the 4 nuts and 2 clamp channels. 3. Remove 2 screws and the gear motor cover. 4. Carefully position the10" discharge plate under the bottom flange of the downdraft. 5. Connect motor plug. 6. Replace the gear motor cover and 2 sheet metal screws. 7. Replace the 2 clamp channels and start the 4 nuts, do not tighten. 8. Slide blower left of right to desired position. Use cover plate (supplied) to close up any open space. 9. Tighten 4 nuts to secure top of blower. Use additional screws (supplied) through bottom flange to secure bottom of discharge plate. CLAMP CHANNELS SCREWS GEARMOTOR COVER NUTS MOTOR PLUG 10" ROUND DISCHARGE PLATE COVER PLATE ADDITIONAL SCREWS BOTTOM FLANGE CUT COUNTERTOP OPENING All Units 1. Measure and cut the countertop opening for your width of cooktop and downdraft. Cooktop Wid th & Model 30" RVGC3305B 30" RVEC3305B 30" CRVGC3305B 30" CRVEC3305B For use with Downdraft Models RVDD330R CRVDD330R 36" RVGC3365B 45" RVEC3456B 36" RVEC3365B 45" CRVEC3456B 36" CRVGC3365B 36" CRVEC3365B RVDD336R CRVDD336R RVDD345R CRVDD345R Cutout Dimensions A B C D E F 29-1/8" 20-5/8" 27" 2-1/4" 1-1/16" 1-1/16" 34-7/8" 20-5/8" 33" 2-1/4" 15/16" 15/16" 42-7/8" 20-5/8" 42" 2-1/4" 7/16" 7/16" E F C D B BLOWER MODEL VIDV500 VEDV900 VEDV1200 DIMENSIONS 18.25" x 18.214" x 7.569" 28.25" x 24.75" x 7.16" 22" x 30.828" x 12.724" A 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
6
Downdraft Ventilators
VIKING RANGE, LLC
PREPARE THE DOWNDRAFT
Exterior Blower Installation
The downdraft is shipped without a blower. Purchase a Model
VEDV900 Exterior Blower and mount the
10" discharge plate
to the downdraft as follows:
1.
Place the downdraft on its back on a table of flat work surface.
2. Remove the
4 nuts
and
2 clamp channels
.
3. Remove
2 screws
and the
gear motor cover
.
4. Carefully position the10" discharge plate under the
bottom
flange
of the downdraft.
5. Connect
motor plug
.
6. Replace the gear motor cover and 2 sheet metal screws.
7.
Replace the 2 clamp channels and start the 4 nuts, do not
tighten.
8. Slide blower left of right to desired position. Use
cover plate
(supplied) to close up any open space.
9.
Tighten 4 nuts to secure top of blower. Use
additional screws
(supplied) through bottom flange to secure bottom of discharge
plate.
NUTS
COVER
PLATE
CLAMP
CHANNELS
SCREWS
GEARMOTOR
COVER
MOTOR
PLUG
10" ROUND
DISCHARGE
PLATE
ADDITIONAL
SCREWS
BOTTOM
FLANGE
CUT COUNTERTOP OPENING
All Units
1. Measure and cut the countertop opening for your width of
cooktop and downdraft.
Cooktop Width & Model
30" RVGC3305B
36" RVGC3365B
45" RVEC3456B
30" RVEC3305B
36" RVEC3365B
45" CRVEC3456B
30" CRVGC3305B
36" CRVGC3365B
30" CRVEC3305B
36" CRVEC3365B
For use with Downdraft Models
RVDD330R
RVDD336R
RVDD345R
CRVDD330R
CRVDD336R
CRVDD345R
Cutout Dimensions
A
29-1/8"
34-7/8"
42-7/8"
B
20-5/8"
20-5/8"
20-5/8"
C
27"
33"
42"
D
2-1/4"
2-1/4"
2-1/4"
E
1-1/16"
15/16"
7/16"
F
1-1/16"
15/16"
7/16"
A
C
B
D
F
E
BLOWER MODEL
DIMENSIONS
VIDV500
18.25" x 18.214" x 7.569"
VEDV900
28.25" x 24.75" x 7.16"
VEDV1200
22" x 30.828" x 12.724"