Viper 4704 Owner Manual - Page 29

Pair Remote - programming

Get Viper 4704 PDF manuals and user guides View all Viper 4704 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Pair Remote Remote pairing is a process where the Responder LC remote, and the in-vehicle system learn the other's encrypted identification, securing communication between the two from intruders. Note: Remotes are pre-programmed from the factory. Prepare the vehicle system to be Paired with a new remote 1. Turn the key to the On position. 2. Within 5 seconds press and release 1 time the Control button on the Control Center. 3. Within 5 seconds, press and hold the Control button. The status LED will flash one time and the horn will honk once to confirm the system is ready for remote pairing. 4. Release the Control button and proceed below. Note: If pairing does not result within 60 seconds, the system exits and the horn honks. Prepare the new remote to be Paired with the system 1. Make sure the remote control is set for the desired Car 1 or Car 2 operation. 2. Perform the steps under Access menu items section to access the Pair Remote mode. 3. When the remote beeps 3 times and PAIR is displayed the remote is ready to pair. 4. Press and hold the button, the horn honks once and the remote will emit several tones to confirm successful pairing. SUCCESS is displayed and the remote returns to the main menu. Note: FAILED will be displayed and the remote will stay in the pair mode in case of an unsuccessful pairing. Check the system status and try again. 26 © 2011 Directed Electronics. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
26
© 2011 Directed Electronics. All rights reserved.
Pair Remote
Remote pairing is a process where the Responder LC remote, and the
in-vehicle system learn the other’s encrypted identification, securing
communication between the two from intruders.
Note:
Remotes are pre-programmed from the factory.
Prepare the vehicle system to be Paired with a new remote
1.
Turn
the key to the On position.
2.
Within 5 seconds
press
and release 1 time the Control button on
the Control Center.
3. Within 5 seconds,
press
and
hold
the Control button. The status
LED will flash one time and the horn will honk once to confirm the
system is ready for remote pairing.
4.
Release
the Control button and proceed below.
Note:
If pairing does not result within 60 seconds, the system exits
and the horn honks.
Prepare the new remote to be Paired with the system
1.
Make sure the remote control is set for the desired Car 1 or Car
2 operation.
2.
Perform the steps under
Access menu items
section to access the
Pair Remote mode.
3. When the remote beeps 3 times and
PAIR
is displayed the
remote is ready to pair.
4.
Press
and
hold
the
button, the horn honks once and the remote
will emit several tones to confirm successful pairing.
SUCCESS
is
displayed and the remote returns to the main menu.
Note:
FAILED
will be displayed and the remote will stay in the pair
mode in case of an unsuccessful pairing. Check the system status and
try again.