Vtech CL82209 User Manual - Page 56

Adding and registering handsets optional, on the handset screen. The handset is now registering

Get Vtech CL82209 PDF manuals and user guides View all Vtech CL82209 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Appendix C Expansion handset Adding and registering handsets (optional) Handsets purchase separately (AT&T CL80109) need to be registered to the telephone base before use. When first purchased, all expansion handsets show NOT REGISTERED on the screen. New handset may need to be charged without interruption for at least 10 minutes before registering to the telephone base. OPU!SFHJTUFSFE To register a handset to your telephone base 1. Make sure the handset is out of the telephone base or charger and shows NOT REGISTERED before you begin registration. 2. Press and hold HANDSET LOCATOR on the telephone base for about four seconds (until the red IN USE light on the telephone base is on) and then release the button. The IN USE light remains on while the telephone base attempts to register a handset. 3. Place the unregistered handset into the telephone base or charger, PRESS HNDST LOC 4 SEC ON BASE shows on the handset screen. The handset is now registering with the telephone base. The handset then shows PLEASE WAIT... and it takes up to 60 seconds to complete the registration. There is a beep sound when the registration is successful. The handset shows HANDSET X REGISTERED, with X being the handset number (1-12). OPU!SFHJTUFSFE QSFTT!IOETU!MPD 5!TFD!PO!CBTF QMFBTF!XBJU/// IBOETFU!Y SFHJTUFSFE NOTES: 1. If the registration is not successful, the screen shows NOT REGISTERED. To reset the handset, remove the handset from the telephone base or charger, then start again from step 2 above. 2. You cannot register a handset if any other system handset is in use. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Appendix C
51
Expansion handset
Adding and registering handsets (optional)
Handsets purchase separately (AT&T CL80109) need to be
registered to the telephone base before use. When first
purchased, all expansion handsets show
NOT REGISTERED
on the screen. New handset may need to be charged
without interruption for at least 10 minutes before
registering to the telephone base.
To register a handset to your telephone base
1. Make sure the handset is out of the telephone base or charger and shows
NOT REGISTERED
before you begin registration.
2. Press and hold
HANDSET LOCATOR
on the
telephone base for about four seconds (until the red
IN
USE
light on the telephone base is on) and then release
the button. The
IN USE
light remains on while the
telephone base attempts to register a handset.
3. Place the unregistered handset into the telephone base
or charger,
PRESS HNDST LOC 4 SEC ON BASE
shows
on the handset screen. The handset is now registering
with the telephone base. The handset then shows
PLEASE WAIT...
and it takes up to 60 seconds to
complete the registration. There is a beep sound when
the registration is successful. The handset shows
HANDSET X REGISTERED
, with
X
being the handset
number (1-12).
NOTES:
1.
If the registration is not successful, the screen shows
NOT REGISTERED
. To reset the
handset, remove the handset from the telephone base or charger, then start again
from step 2 above.
2.
You cannot register a handset if any other system handset is in use.
IBOETFU
Y
SFHJTUFSFE
OPU
SFHJTUFSFE
QSFTT
IOETU
MPD
5
TFD
PO
CBTF
QMFBTF
XBJU///
OPU
SFHJTUFSFE