Vtech VCS754 Administrator and Provisioning Manual - Rev 4 - Page 12

Network Requirements

Get Vtech VCS754 PDF manuals and user guides View all Vtech VCS754 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

VCS754 Administrator and Provisioning Manual Network Requirements A simple VCS754 SIP Conference Phone with Four Wireless Mics installation example is shown in Figure 1. A switched network topology is recommended for your LAN (using standard 10/100 Ethernet switches that carry traffic at a nominal rate of 100 Mbit/s). The office LAN infrastructure should use Cat.-5/Cat.-5e cable. The VCS754 requires a wired connection to the LAN. However, wireless connections from your LAN to other devices (such as laptops) in your office will not impede performance. A Dynamic Host Configuration Protocol (DHCP) server is recommended and must be on the same subnet as the VCS754 conference phones so that IP addresses can be auto-assigned. In most cases, your network router will have a DHCP server. By default, the VCS754 has DHCP enabled for automatic IP address assignment. Some DHCP servers have default settings that limit the number of network IP addresses assigned to devices on the network. You should log in to your server to confirm that the IP range is sufficient. If no DHCP server is present, you can assign a static IP to the VCS754. You can assign a static IP address using the VCS754 menu. Go to Admin settings > Network setting > Set static IP. If you do not have a DHCP server or do not manually assign static IPs, you will not be able to access the WebUI and/or enable automatic time updates from an NTP server. A DNS server is recommended to resolve the path to the Internet and to a server for firmware and configuration updates. If necessary, the system administrator can also download upgrade files and use the WebUI to update the VCS754 firmware and/or configuration settings manually. Figure 1. VCS754 Installation Example Introducing the VCS754 12 Back to Contents

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
Introducing the VCS754
12
Back to Contents
VCS754 Administrator and Provisioning Manual
Network Requirements
A simple VCS754 SIP Conference Phone with Four Wireless Mics installation example is
shown in Figure 1. A switched network topology is recommended for your LAN (using
standard 10/100 Ethernet switches that carry traffic at a nominal rate of 100 Mbit/s).
The office LAN infrastructure should use Cat.-5/Cat.-5e cable.
The VCS754 requires a wired connection to the LAN. However, wireless connections from
your LAN to other devices (such as laptops) in your office will not impede performance.
A Dynamic Host Configuration Protocol (DHCP) server is recommended and must be on
the same subnet as the VCS754 conference phones so that IP addresses can be
auto-assigned. In most cases, your network router will have a DHCP server. By default, the
VCS754 has DHCP enabled for automatic IP address assignment.
If no DHCP server is present, you can assign a static IP to the VCS754. You can assign a
static IP address using the VCS754 menu. Go to
Admin settings > Network setting > Set
static IP
. If you do not have a DHCP server or do not manually assign static IPs, you will
not be able to access the WebUI and/or enable automatic time updates from an NTP
server.
A DNS server is recommended to resolve the path to the Internet and to a server for
firmware and configuration updates. If necessary, the system administrator can also
download upgrade files and use the WebUI to update the VCS754 firmware and/or
configuration settings manually.
Figure 1. VCS754 Installation Example
Some DHCP servers have default settings that limit the number of network IP
addresses assigned to devices on the network. You should log in to your server
to confirm that the IP range is sufficient.