Waring WDM360 Instruction Manual - Page 5

Unplug Power Cord From Electrical Outlet Before - drink mixer

Get Waring WDM360 PDF manuals and user guides View all Waring WDM360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

6. Working from the top down, wash, rinse, and sanitize the portion of the mixer housing situated directly over the container and the portion of the spindle above the agitator, using absorbent wiping cloths moistened with cleaning solution, rinse water and sanitizing solution. 7. Reassemble upper cup holder and cup supports to mixer housing by reversing steps 3 and 4. 8. For each spindle wash, rinse, and sanitize the bottom of the spindle and the agitator (Illustration A and B) as follows: Plug the Waring® Drink Mixer cord into electrical outlet. For each spindle, add 8 ounces of washing solution to container and place in normal operating position on mixer. Run on high speed for a minimum of two (2) minutes. Empty container and repeat two-minute run with 8 ounces of water. Empty container and repeat two-minute run with 8 ounces of sanitizing solution. Empty container. Run motor for a few seconds with empty container in normal operating position to spin off any excess moisture. Do not rinse container, spindle or agitator after sanitizing is completed. Allow all parts to air dry. Wash, rinse, and sanitize as outlined above prior to initial use and whenever mixer will not be used again within a period of one hour to avoid bacteria build up. Surfaces of the mixer housing that are outside of the food contact areas may be cleaned as required, using wiping cloths moistened with cleaning solution, rinse water and sanitizing solution. UNPLUG POWER CORD FROM ELECTRICAL OUTLET BEFORE CLEANING HOUSING. Prevent liquid from running into housing by wringing all excess moisture from wiping cloths before using them. Washing solutions based on non-sudsing detergents and chlorine-based sanitizing solutions having a minimum chlorine concentration of 100 PPM are recommended. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
5
6.
Working from the top down, wash, rinse, and sanitize the
portion of the mixer housing situated directly over the
container and the portion of the spindle above the agitator,
using absorbent wiping cloths moistened with cleaning
solution, rinse water and sanitizing solution.
7.
Reassemble upper cup holder and cup supports to mixer
housing by reversing steps 3 and 4.
8.
For each spindle wash, rinse, and sanitize the bottom of the
spindle and the agitator (Illustration A and B) as follows:
Plug the Waring
®
Drink Mixer cord into electrical outlet.
For each spindle, add 8 ounces of washing solution to
container and place in normal operating position on mixer.
Run on high speed for a minimum of two (2) minutes.
Empty container and repeat two-minute run with 8 ounces
of water.
Empty container and repeat two-minute run with 8 ounces
of sanitizing solution.
Empty container. Run motor for a few seconds with empty
container in normal operating position to spin off any excess
moisture. Do not rinse container, spindle or agitator after
sanitizing is completed. Allow all parts to air dry.
Wash, rinse, and sanitize as outlined above prior to initial use and
whenever mixer will not be used again within a period of one hour
to avoid bacteria build up.
Surfaces of the mixer housing that are outside of the food contact
areas may be cleaned as required, using wiping cloths moistened
with cleaning solution, rinse water and sanitizing solution.
UNPLUG POWER CORD FROM ELECTRICAL OUTLET BEFORE
CLEANING HOUSING. Prevent liquid from running into housing
by wringing all excess moisture from wiping cloths before using
them.
Washing solutions based on non-sudsing detergents and
chlorine-based sanitizing solutions having a minimum chlorine
concentration of 100 PPM are recommended.