Waring WDM500 Instruction Manual - Page 4

Cleaning & Maintenance Instructions

Get Waring WDM500 PDF manuals and user guides View all Waring WDM500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

to allow mix residues to spin off agitator and be retained in cup. IMPORTANT: DO NOT RUSH THE MIXING PROCESS! The secret to complete mixing is to work slowly. Proper mixing requires 10-20 seconds (5-10 seconds up, and 5-10 seconds down). 7. Set toggle switch to "OFF" position. 8. The Pulse switch will operate at whatever speed the dial is set to. The Pulse switch will only operate while pressed forward or backward. Keep a firm grip on the cup while using the Pulse switch. CLEANING & MAINTENANCE INSTRUCTIONS 1. Add 36 ounces of clean rinse water to metal mixing cup. Bring cup into normal operation position and run for two (2) minutes. Empty cup. 2. UNPLUG MIXER POWER CORD FROM ELECTRICAL OUTLET. 3. Remove clear plastic splash shield by lifting straight up until it clears the top of the mixer housing. 4. Remove left and right splash shield guide tracks (the grooved plastic posts in which the splash shield slides up and down) by tilting their top ends inward and lifting out. 5. Wash, rinse and sanitize the splash shield and both guide tracks. Sanitize these parts by immersion in sanitizing solution for two (2) minutes. Shake off excess moisture and allow to air dry. CAUTION: High temperatures may distort the splash shield and guide tracks. These parts must be hand-washed. DO NOT PUT IN DISHWASHER. 6. Working from the top down, wash, rinse and sanitize all parts of the mixer housing located above, around and below the spindle and agitator, and that portion of the spindle itself which is above the agitator using absorbent wiping cloths moistened with cleaning solution, rinse water and sanitizing solution. 7. Reassemble the splash shield guide tracks and the splash shield to the mixer housing. 8. Wash, rinse and sanitize the agitator as follows. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
4
to allow mix residues to spin off agitator and be retained
in cup.
IMPORTANT: DO NOT RUSH THE MIXING PROCESS! The secret
to complete mixing is to work slowly. Proper mixing requires
10–20 seconds (5–10 seconds up, and 5–10 seconds down).
7.
Set toggle switch to “OFF” position.
8.
The Pulse switch will operate at whatever speed the dial
is set to. The Pulse switch will only operate while pressed
forward or backward. Keep a firm grip on the cup while
using the Pulse switch.
CLEANING & MAINTENANCE INSTRUCTIONS
1.
Add 36 ounces of clean rinse water to metal mixing cup.
Bring cup into normal operation position and run for two (2)
minutes. Empty cup.
2.
UNPLUG MIXER POWER CORD FROM ELECTRICAL
OUTLET.
3.
Remove clear plastic splash shield by lifting straight up until
it clears the top of the mixer housing.
4.
Remove left and right splash shield guide tracks (the
grooved plastic posts in which the splash shield slides up
and down) by tilting their top ends inward and lifting out.
5.
Wash, rinse and sanitize the splash shield and both guide
tracks. Sanitize these parts by immersion in sanitizing
solution for two (2) minutes. Shake off excess moisture and
allow to air dry.
CAUTION: High temperatures may distort the splash shield
and guide tracks. These parts must be hand-washed.
DO NOT PUT IN DISHWASHER.
6.
Working from the top down, wash, rinse and sanitize all
parts of the mixer housing located above, around and below
the spindle and agitator, and that portion of the spindle itself
which is above the agitator using absorbent wiping cloths
moistened with cleaning solution, rinse water and sanitizing
solution.
7.
Reassemble the splash shield guide tracks and the splash
shield to the mixer housing.
8.
Wash, rinse and sanitize the agitator as follows.