Waring WFP14SC Instruction Manual - Page 8

Disassembly Of Batch Bowl Parts, Wfp14sc

Get Waring WFP14SC PDF manuals and user guides View all Waring WFP14SC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

DISASSEMBLY of BATCH BOWL PARTS WFP14SC ALWAYS UNPLUG THE CORD BEFORE DISASSEMBLING. • Turn the bowl cover clockwise until the safety interlock tab on the cover is disengaged and the locking tabs are clear of the tabs on the bowl. In this position you can lift the cover off the bowl. • Remove the large food pusher from the feed tube. Remove the small pusher from the large pusher. Disassembly when removing the S-blade • Remove the work bowl from the unit by rotating clockwise (left) to disengage the tabs on the bottom of the bowl platform from the work bowl. When the bowl handle is on the left (about 7 o'clock position), you can gently lift the bowl straight up and out. It is recommended that you remove the bowl from the motor base before you remove the S-blade. • To remove the blade, keep a slight downward pressure on the top of the center hub of the blade while removing the bowl from the motor base. This will form a seal to prevent food particles from spilling into the center tube of the bowl and onto the motor base or the work surface. REMOVE ALL FOOD AND LIQUID BEFORE REMOVING S-BLADE, OR BOWL WILL LEAK. Then remove the S-blade from the bowl by pulling upward to unlock the seal. Handle the S-blade with caution; the blades are extremely sharp. Disassembly when removing an accessory disc • Do not remove the work bowl until the accessory disc is removed. • To remove an accessory disc, place your fingers on the outer edge of two opposite sides of the disc and lift. The disc should remove cleanly. To remove the detachable stem, hold the disc in one hand with the stem facing away from your hand. Be careful not to scrape your hand on any sharp edges; depress the release switch with your thumb and rotate counterclockwise. • Remove the work bowl from the unit by rotating clockwise to disengage the tabs on the bottom of the bowl platform from the work bowl. When the bowl handle is on the left (about 7 o'clock position), you can gently lift the bowl straight up and out. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
8
DISASSEMBLY OF BATCH BOWL PARTS
WFP14SC
ALWAYS UNPLUG THE CORD BEFORE DISASSEMBLING.
• Turn the bowl cover clockwise until the safety interlock tab on the cover is disengaged and the lock
-
ing tabs are clear of the tabs on the bowl. In this position you can lift the cover off the bowl.
• Remove the large food pusher from the feed tube. Remove the small pusher from the large pusher.
Disassembly when removing the S-blade
• Remove the work bowl from the unit by rotating clockwise (left) to disengage the tabs on the bottom
of the bowl platform from the work bowl. When the bowl handle is on the left (about 7 o’clock
position), you can gently lift the bowl straight up and out.
It is recommended that you remove the bowl from the motor base before you
remove the S-blade.
• To remove the blade, keep a slight downward pressure on the top of the center hub of the blade
while removing the bowl from the motor base. This will form a seal to prevent food particles from
spilling into the center tube of the bowl and onto the motor base or the work surface.
REMOVE
ALL FOOD AND LIQUID BEFORE REMOVING S-BLADE, OR BOWL WILL LEAK.
Then remove the S-blade from the bowl by pulling upward to unlock the seal. Handle the S-blade
with caution; the blades are extremely sharp.
Disassembly when removing an accessory disc
• Do not remove the work bowl until the accessory disc is removed.
• To remove an accessory disc, place your fingers on the outer edge of two opposite sides of the disc
and lift. The disc should remove cleanly. To remove the detachable stem, hold the disc in one hand
with the stem facing away from your hand. Be careful not to scrape your hand on any sharp edges;
depress the release switch with your thumb and rotate counterclockwise.
• Remove the work bowl from the unit by rotating clockwise to disengage the tabs on the bottom
of the bowl platform from the work bowl. When the bowl handle is on the left (about 7 o’clock
position), you can gently lift the bowl straight up and out.