Weslo 925 Instruction Manual - Page 6

How To Lower The Treadmill For Use

Get Weslo 925 PDF manuals and user guides View all Weslo 925 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

4. Insert all excess wire through the right Handrail (51) and down into the right Upright (1). 4 Attach the right Handrail (51) to the right Upright (1) with two Upright Screws (50) and an Upright Washer (82). Be sure to start both Screws before tightening either one, 17 and push on the heads of the Screws whilst tightening them. Position the Console Base (8) on the left and right Handrails (51). Attach the Console with four Console Screws (17). 8 17 50 82 1 51 51 5. Attach the Frame Guide (68) and two Frame Guide Spacers (93) to the Frame (66) with two Latch Screws (17). Be careful not to overtighten the Screws. Note: If the Frame Guides hit the upright when you fold the treadmill to the storage position, use only one Spacer. Make sure that the latch closes over the Frame Guide when in the storage position. 6. Remove the backing from the Adhesive Clip (16). Press the Adhesive Clip onto the Rear Roller Endcap (86) in the indicated location. Press the Allen Wrench (62) into the Adhesive Clip. 5 93 68 17 66 Thick End 6 86 62 50 16 7. Make sure that all parts are tightened before you use the treadmill. Note: To protect the floor or carpet, place a mat under the treadmill. HOW TO MOVE THE TREADMILL Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the storage latch is closed fully over the frame guide. 1. Hold the upper ends of the handrails. Place one foot on the leg as shown. 2. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back, or the leg pads may come off. To reduce the risk of injury, use extreme caution whilst moving the treadmill. Do not attempt to move the treadmill over an uneven surface. 3. Place one foot on the leg, and carefully lower the treadmill until it is resting in the storage position. HOW TO LOWER THE TREADMILL FOR USE 1. Hold the upper end of the treadmill with your right hand as shown. Using your left thumb, slide open the storage latch and hold it open. Pivot the treadmill until the frame and foot rail are past the storage latch. 2. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. To decrease the possibility of injury, bend your legs and keep your back straight. Leg Front Wheels Storage Latch Opened 6 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
11
6
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above.
Make sure that the stor-
age latch is closed fully over the frame guide.
1. Hold the upper ends of the handrails. Place one foot on
the leg as shown.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location.
Never
move the treadmill without tipping it back, or the leg
pads may come off. To reduce the risk of injury, use
extreme caution whilst moving the treadmill. Do not
attempt to move the treadmill over an uneven surface.
3. Place one foot on the leg, and carefully lower the treadmill
until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left thumb, slide open the storage latch
and hold it open. Pivot the treadmill until the frame and
foot rail are past the storage latch.
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor.
To decrease the possibility of in-
jury, bend your legs and keep your back straight.
4.
Insert all excess wire through the right Handrail (51) and
down into the right Upright (1).
Attach the right Handrail (51) to the right Upright (1) with
two Upright Screws (50) and an Upright Washer (82). Be
sure to start both Screws before tightening either one,
and push on the heads of the Screws whilst tightening
them.
Position the Console Base (8) on the left and right
Handrails (51). Attach the Console with four Console
Screws (17).
5. Attach the Frame Guide (68) and two Frame Guide
Spacers (93) to the Frame (66) with two Latch Screws
(17). Be careful not to overtighten the Screws. Note: If
the Frame Guides hit the upright when you fold the tread-
mill to the storage position, use only one Spacer. Make
sure that the latch closes over the Frame Guide when in
the storage position.
6. Remove the backing from the Adhesive Clip (16). Press
the Adhesive Clip onto the Rear Roller Endcap (86) in
the indicated location. Press the Allen Wrench (62) into
the Adhesive Clip.
7.
Make sure that all parts are tightened before you use the treadmill.
Note: To protect the floor or carpet,
place a mat under the treadmill.
16
86
62
1
8
51
51
17
17
50
82
50
4
6
66
Thick
End
68
93
17
5
Storage
Latch
Opened
Leg
Front Wheels