Weslo Cadence 1000 Fm Uk Manual - Page 7

Attach the Latch Housing 46 to the Left Upright 47

Get Weslo Cadence 1000 Fm PDF manuals and user guides View all Weslo Cadence 1000 Fm manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

3. Hold an Upright Spacer (59) against one side of the Frame (96) as shown. Insert a 4" Frame Bolt (54) into the indicated hole in the Upright Spacer and the Frame. Next, tighten a 3/4" Tek Screw (9) into the Upright Spacer and the Frame. Then, remove the 4" Frame Bolt. Repeat this procedure on the other side of the Frame. Have a second person lift the front end of the Frame (96). Insert a 4" Frame Bolt (54) with a 3/8" Washer (12) and a 3/8" Star Washer (55) into the Right Upright (104) and the right Upright Spacer (59), and tighten the Frame Bolt into the Frame. Do not overtighten the Frame Bolt. Repeat this procedure on the left side of the Frame. 3 96 9 59 104 55 12 54 Hole 4. Attach the Latch Housing (46) to the Left Upright (47) with 4 two 3/4" Screws (38). Make sure that the large hole in the Latch Housing is on the side shown. 47 46 38 Large Hole 5. Identify the Right Handrail (40), which has a pulse bar bracket on its left side. Feed the Wire Harness (65) up into the large bracket on the Right Handrail and out of the large hole in the left side. (Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the hole.) Remove any nylon ties from the large bracket. Insert the large bracket on the Right Handrail (40) into the upper end of the Right Upright (104). Attach the Right Handrail with two 1" Bolts (43), two 1/4" Washers (44), two 1/4" Star Washers (45), a 4" Handrail Bolt (78), and a 5/16" Washer (106) as shown. Do not tighten the Bolts yet. See drawing 5a. Insert the included nylon tie through the indicated hole in the Right Handrail (40). See drawing 5b. Look into the Right Handrail and make sure that the Wire Harness (65) is secured to the side shown. Then, tighten the nylon tie and cut the excess off the end. Attach the Left Handrail (not shown) in the same way. Note: You may need to tip the Left Handrail to one side as you insert the bracket. There is not a wire harness in the left Upright (not shown). 7 5 65 Large Hole 40 Pulse Bar Bracket Large Bracket 43 44 45 104 43 44 45 78 106 5a Tie 5b Tie 40 40 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
7
5.
Identify the Right Handrail (40), which has a pulse bar
bracket on its left side. Feed the Wire Harness (65) up
into the large bracket on the Right Handrail and out of
the large hole in the left side. (Note: It may be helpful to
use needlenose pliers to pull the Wire Harness out of the
hole.) Remove any nylon ties from the large bracket.
Insert the large bracket on the Right Handrail (40) into
the upper end of the Right Upright (104). Attach the Right
Handrail with two 1” Bolts (43), two 1/4” Washers (44),
two 1/4” Star Washers (45), a 4” Handrail Bolt (78), and a
5/16” Washer (106) as shown.
Do not tighten the Bolts
yet.
See drawing 5a. Insert the included nylon tie through the
indicated hole in the Right Handrail (40). See drawing 5b.
Look into the Right Handrail and make sure that the Wire
Harness (65) is secured to the side shown. Then, tighten
the nylon tie and cut the excess off the end.
Attach the Left Handrail (not shown) in the same way.
Note: You may need to tip the Left Handrail to one side
as you insert the bracket. There is not a wire harness in
the left Upright (not shown).
3. Hold an Upright Spacer (59) against one side of the
Frame (96) as shown. Insert a 4” Frame Bolt (54) into the
indicated hole in the Upright Spacer and the Frame.
Next, tighten a 3/4” Tek Screw (9) into the Upright
Spacer and the Frame. Then, remove the 4” Frame Bolt.
Repeat this procedure on the other side of the Frame.
Have a second person lift the front end of the Frame
(96). Insert a 4” Frame Bolt (54) with a 3/8” Washer (12)
and a 3/8” Star Washer (55) into the Right Upright (104)
and the right Upright Spacer (59), and tighten the Frame
Bolt into the Frame.
Do not overtighten the Frame
Bolt.
Repeat this procedure on the left side of the Frame.
3
55
12
96
Hole
54
104
9
59
65
43
44
104
45
43
44
45
40
40
78
106
Large
Hole
Large Bracket
Pulse Bar Bracket
5
5a
5b
Tie
Tie
65
40
4. Attach the Latch Housing (46) to the Left Upright (47) with
two 3/4” Screws (38).
Make sure that the large hole in
the Latch Housing is on the side shown.
46
38
47
Large Hole
4