Weslo Cadence 5.0 Treadmill Uk Manual - Page 7

Press the Right Frame Spacer 13

Get Weslo Cadence 5.0 Treadmill PDF manuals and user guides View all Weslo Cadence 5.0 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

2. Open part bag B. Press the Right Frame Spacer (13) and the Left Frame Spacer (not shown) onto the sides of the Frame (55) as shown. Make sure that the high side of each Spacer is facing forward as shown. With the help of a second person, carefully lift the Frame and hold the Spacers between the plates on the Uprights (89). Align the hole in the plate on the Right Upright (89) with the hole in the Right Frame Spacer (13). Loosely thread a 5" Bolt (10) and a 3/8" Star Washer (45) into the Spacer and the Frame (55). Repeat this step on the left side of the treadmill. See drawing 2a. With the help of a second person, carefully tip the treadmill onto its left side as shown. Feed the Wire Harness (22) into the large round hole near the lower end of the Right Upright (89), and then pull the Wire Harness out of the upper end as shown. 2 Wide side Plate 13 55 2a 89 22 45 89 10 22 3. Open part bag C. With the help of a second person, raise the Left and Right Uprights (88, 89) to the vertical position. Identify the Right Handrail (6), which has a large hole in the left side. Feed the Wire Harness (22) into the rectangular bracket on the Right Handrail and out of the large hole. Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the hole. Insert the rectangular bracket on the Right Handrail (6) into the right Upright (89). Attach the Right Handrail with two 1" Bolts (12) and two 1/4" Washers (107) as shown. Do not tighten the Bolts yet. Attach the Left Handrail (7) as described above. Note: There is not a wire harness on the left side. 4. See the inset drawings and identify the two Crossbar Screws (69); be careful not to confuse the Crossbar Screws with the 3/4" Screws (90). Hold the Crossbar (75) on the small brackets on the Handrails (6, 7). Attach the Crossbar to the small brackets with the two Crossbar Screws (69). Do not tighten the Crossbar Screws yet. Attach the end of the ground wire to the small hole in the side of the Right Handrail (6) with a Silver Ground Screw (87). 3 7 12 107 88 12 22 Hole 12 6 107 12 89 4 Small Bracket 75 22 69 7 87 Small Bracket 6 69 69 90 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
7
3.
Open part bag C.
With the help of a second person,
raise the Left and Right Uprights (88, 89) to the vertical
position.
Identify the Right Handrail (6), which has a large hole in
the left side. Feed the Wire Harness (22) into the rectan-
gular bracket on the Right Handrail and out of the large
hole. Note: It may be helpful to use needlenose pliers to
pull the Wire Harness out of the hole.
Insert the rectangular bracket on the Right Handrail (6)
into the right Upright (89). Attach the Right Handrail with
two 1” Bolts (12) and two 1/4” Washers (107) as shown.
Do not tighten the Bolts yet.
Attach the Left Handrail (7) as described above. Note:
There is not a wire harness on the left side.
22
Hole
12
12
6
12
12
107
7
107
88
89
3
45
10
Wide
side
Plate
89
55
2.
Open part bag B.
Press the Right Frame Spacer (13) and
the Left Frame Spacer (not shown) onto the sides of the
Frame (55) as shown.
Make sure that the high side of
each Spacer is facing forward as shown.
With the help
of a second person, carefully lift the Frame and hold the
Spacers between the plates on the Uprights (89).
Align the hole in the plate on the Right Upright (89) with
the hole in the Right Frame Spacer (13). Loosely thread a
5” Bolt (10) and a 3/8” Star Washer (45) into the Spacer
and the Frame (55).
Repeat this step on the left side of
the treadmill.
See drawing 2a. With the help of a second person, care-
fully tip the treadmill onto its left side as shown.
Feed the Wire Harness (22) into the large round hole near
the lower end of the Right Upright (89), and then pull the
Wire Harness out of the upper end as shown.
13
2
75
22
4
69
69
7
6
87
4.
See the inset drawings and identify the two Crossbar
Screws (69);
be careful not to confuse the Crossbar
Screws with the 3/4” Screws (90).
Hold the Crossbar (75) on the small brackets on the
Handrails (6, 7). Attach the Crossbar to the small brack-
ets with the two Crossbar Screws (69).
Do not tighten
the Crossbar Screws yet.
Attach the end of the ground wire to the small hole in the
side of the Right Handrail (6) with a Silver Ground Screw
(87).
69
2a
22
22
89
Small Bracket
Small Bracket
90