Weslo Cadence Af 5.1 Treadmill English Manual - Page 16

Troubleshooting

Get Weslo Cadence Af 5.1 Treadmill PDF manuals and user guides View all Weslo Cadence Af 5.1 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

TROUBLESHOOTING Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual. SYMPTOM: The power does not turn on a. Make sure that the power cord is plugged into a surge suppressor and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppressor that meets all of the specifications described on page 10. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets. SYMPTOM: The displays of the console do not function properly a. Remove the key from the console and UNPLUG THE POWER CORD. Next, remove the three M4.2 x 19mm Washer Head Screws (20) and the two indicated M5.5 x 25mm Screws (25). Then, carefully remove the Hood (65). a 65 20 25 b. After the power cord has been plugged in, make sure that the key is inserted into the console. c. Check the power switch located on the treadmill frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in. c Tripped Reset Locate the Reed Switch (89) and the Magnet (62) on the left side of the Pulley (71). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the M4.2 x 13mm Tek Screw (3), move the Reed Switch slightly, and then retighten the Screw. Then, reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading. SYMPTOM: The power turns off during use a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in. c. Remove the key from the console, and then reinsert it. d. If the treadmill still will not run, please see the front cover of this manual. Top View 1/8 in. 3 89 71 62 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
16
Most treadmill problems can be solved by following
the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assis-
tance is needed, see the front cover of this manual.
SYMPTOM: The power does not turn on
a.
Make sure that the power cord is plugged into a
surge suppressor and that the surge suppressor is
plugged into a properly grounded outlet (see page
10). Use only a single-outlet surge suppressor that
meets all of the specifications described on page
10.
IMPORTANT: The treadmill is not compati-
ble with GFCI-equipped outlets and may not be
compatible with AFCI-equipped outlets.
b.
After the power cord has been plugged in, make
sure that the key is inserted into the console.
c.
Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for five minutes and then press
the switch back in.
SYMPTOM: The power turns off during use
a.
Check the power switch (see the drawing above). If
the switch has tripped, wait for five minutes and
then press the switch back in.
b.
Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c.
Remove the key from the console, and then
reinsert it.
d.
If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The displays of the console do not
function properly
a.
Remove the key from the console and
UNPLUG
THE POWER CORD.
Next, remove the three M4.2
x 19mm Washer Head Screws (20) and the two in-
dicated M5.5 x 25mm Screws (25). Then, carefully
remove the Hood (65).
Locate the Reed Switch (89) and the Magnet (62)
on the left side of the Pulley (71). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet
and the Reed Switch is about 1/8 in. (3 mm).
If
necessary, loosen the M4.2 x 13mm Tek Screw
(3), move the Reed Switch slightly, and then
retighten the Screw. Then, reattach the Hood (not
shown), and run the treadmill for a few minutes to
check for a correct speed reading.
Tripped
Reset
c
20
65
a
62
3
89
Top
View
1/8 in.
71
TROUBLESHOOTING
25