Weslo Gym 750 Uk Manual - Page 11

Locate the Short Cable 47.

Get Weslo Gym 750 PDF manuals and user guides View all Weslo Gym 750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

18. Wrap the Press Cable (49) under a 90mm Pulley 18 (34). Attach the Pulley and two Finger Guards (35) to the Double "U"-bracket (42) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut (68). 19. Apply grease to an M10 x 78mm Bolt (54). Attach 19 the Pulley Arm (38) to the Upright (3) with the Bolt and an M10 Nylon Locknut (68). Do not over- tighten the Locknut; the Pulley Arm must be able to pivot easily. Wrap the Press Cable (49) over a 90mm Pulley (34). Attach the Pulley, a Cable Trap (36), an M10 Washer (70), and two Finger Guards (35) to the indicated side of a Pulley Arm (38) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 49 34 35 68 35 53 42 52 54 38 35 36 68 49 34 70 35 68 3 20. Slide the end of the Press Cable (49) onto the hook on the Right Arm (6). 20 49 6 21. Locate the Short Cable (47). Attach the eyelet 21 on the Cable to the Base (1) with an M10 x 70mm Bolt (57), an M10 Washer (70), and an M10 Nylon Locknut (68). Do not overtighten the Locknut. 70 68 1 57 47 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
11
19. Apply grease to an M10 x 78mm Bolt (54). Attach
the Pulley Arm (38) to the Upright (3) with the Bolt
and an M10 Nylon Locknut (68).
Do not over-
tighten the Locknut; the Pulley Arm must be
able to pivot easily.
Wrap the Press Cable (49) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), an M10
Washer (70), and two Finger Guards (35) to the
indicated side of a Pulley Arm (38) with an M10 x
52mm Bolt (52) and an M10 Nylon Locknut (68).
Make sure that the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
18. Wrap the Press Cable (49) under a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Double “U”-bracket (42) with an M10 x
46mm Bolt (53) and an M10 Nylon Locknut (68).
34
53
68
49
35
42
35
18
35
36
49
52
38
68
68
3
54
34
35
70
19
20. Slide the end of the Press Cable (49) onto the
hook on the Right Arm (6).
49
6
20
21.
Locate the Short Cable (47).
Attach the eyelet
on the Cable to the Base (1) with an M10 x
70mm Bolt (57), an M10 Washer (70), and an
M10 Nylon Locknut (68).
Do not overtighten the
Locknut.
57
70
68
47
1
21