Weslo Pursuit 895i Bike User Manual - Page 13

How To Adjust The Pedal Straps

Get Weslo Pursuit 895i Bike PDF manuals and user guides View all Weslo Pursuit 895i Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

HOW TO ADJUST THE RESISTANCE STRAP If there is not enough pedalling resistance when the resistance knob is turned to the highest setting, the Resistance Strap (47) may need to be adjusted. To adjust the Resistance Strap, the left side shield must first be removed. Refer to the instructions at the left and remove the left side shield. Next, turn the resistance knob to the lowest set- ting. Locate and open the Strap 17 Buckle (46). Grip 47 the end of the Resistance Strap (47) and pull it up to remove any 46 slack. Whilst holding the end of the Resistance Strap, fully close the Strap Buckle. Turn the Crank (17) for a moment to make sure that there is not too much resistance. When the Resis- tance Strap is properly adjusted, reattach the left side shield and pedal. HOW TO ADJUST THE BELT The exercise cycle features a precision belt that must be 16 kept properly adjusted. If the belt causes excessive noise or slips as you pedal, the belt should be checked. To do this, the left side shield must first be removed. Refer to the instructions on page 12 and remove the left side shield. Next, use an adjustable wrench to turn the right pedal counterclockwise and remove it. Remove the right side shield. Press down on the centre of the Belt (16) between the front and rear sprockets. There should be from 1/4" to 3/4" of vertical movement in the centre of the Belt. If the Belt (16) is properly adjusted, reat- 16 tach the side shields and ped- 34 als. If the Belt 39 needs to be adjusted, loosen the M10 Washer Nut 37 (34) on each side of the Flywheel (39). To tighten the Belt, turn the two M6 Nuts (37) clockwise; to loosen the belt, turn the Nuts counterclockwise. Make sure that the Flywheel is straight and tighten the M10 Washer Nuts (34). Reattach the side shields and pedals. HOW TO ADJUST THE PEDAL STRAPS To adjust the Left Pedal Strap (64), first pull the end of the Pedal Strap off 45 28 the adjustment tab on the Pedal (28). Align a different hole in the Adjustment Tab Pedal Strap with the adjust- ment tab. Press the Pedal Strap onto the adjustment tab. Do the same to adjust the Right Pedal Strap (not shown). 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
HOW TO ADJUST THE RESISTANCE STRAP
If there is not enough pedalling resistance when the
resistance knob is turned to the highest setting, the
Resistance Strap (47) may need to be adjusted. To
adjust the Resistance Strap, the left side shield must
first be removed. Refer to the instructions at the left
and remove the left side shield.
Next, turn the
resistance knob
to the lowest set-
ting. Locate and
open the Strap
Buckle (46). Grip
the end of the
Resistance Strap
(47) and pull it up
to remove any
slack. Whilst
holding the end
of the Resistance Strap,
fully
close the Strap Buckle.
Turn the Crank (17) for a moment to make sure that
there is not too much resistance. When the Resis-
tance Strap is properly adjusted, reattach the left side
shield and pedal.
HOW TO ADJUST THE BELT
The exercise
cycle features a
precision belt
that must be
kept properly
adjusted. If the
belt causes
excessive noise
or slips as you
pedal, the belt
should be
checked. To do
this, the left side shield must first be removed. Refer
to the instructions on page 12 and remove the left
side shield. Next, use an adjustable wrench to turn
the right pedal counterclockwise and remove it.
Remove the right side shield. Press down on the cen-
tre of the Belt (16) between the front and rear sprock-
ets.
There should be from 1/4” to 3/4” of vertical
movement in the centre of the Belt.
If the Belt (16)
is properly
adjusted, reat-
tach the side
shields and ped-
als. If the Belt
needs to be
adjusted, loosen
the M10
Washer Nut
(34) on each
side of the
Flywheel (39). To tighten the Belt, turn the two M6
Nuts (37) clockwise; to loosen the belt, turn the Nuts
counterclockwise. Make sure that the Flywheel is
straight and tighten the M10 Washer Nuts (34). Reattach
the side shields and pedals.
HOW TO ADJUST THE PEDAL STRAPS
To adjust the
Left Pedal Strap
(64), first pull
the end of the
Pedal Strap off
the adjustment
tab on the
Pedal (28).
Align a different
hole in the
Pedal Strap
with the adjust-
ment tab. Press the Pedal Strap onto the adjustment
tab. Do the same to adjust the Right Pedal Strap (not
shown).
13
46
17
47
16
16
39
34
37
45
28
Adjustment Tab