Home » Western Digital Manuals » Network Storage Servers » Western Digital WDA4NC40000N » Manual Viewer

Western Digital WDA4NC40000N User Guide - Page 184

Remove the drive carrier., Remove the new hard drive from its packaging., Install the new drive into

UPC - 718037733654

View all Western Digital WDA4NC40000N manuals

Add to My Manuals
Save this manual to your list of manuals

Page 184 highlights

WD SHARESPACE USER MANUAL (b) While pulling out the drive assembly with one hand, use your other hand to support the drive while sliding it out of the enclosure. 7. Remove the drive carrier. (a) Flex the back pin of the side rail from the hard drive and gently pull the side-rail away from the hard drive. (b) Remove the drive from the drive carrier. 8. Remove the new hard drive from its packaging. 9. Install the new drive into the drive carrier. (a) Insert the new drive into the drive carrier. (b) Flex the left and right-side rail and insert the pins into the drive's mounting holes. REPLACING A DRIVE - 179

Section	Page
WD ShareSpace™	1
Important Safety Instructions	2
(a) When the power cord or plug is damaged or frayed.	2
Table of Contents	3
WD Service and Support	6
Accessing Online Support	6
Contacting WD Technical Support	6
Registering Your WD Product	7
Overview	8
Format and Configuration	8
WD ShareSpace File Storage	8
Specifications	10
Kit Contents	11
Accessories	11
System Requirements	11
Client computer	11
Local network	12
Wide Area Network	12
Pre-installation	12
Recording Your WD Product Information	12
System View	13
Power Button	13
LED Indicators	14
USB Backup Button	15
Ports	15
Reset Button	15
Kensington Hardware Features	15
Security Slot	15
WD ShareSpace Basic Setup	16
Step 1: Connect WD ShareSpace to the Network	16
1. Connect one end of the Ethernet cable into the Ethernet port located on the back of the device. Connect the other end of the Ethernet cable directly into a router or network switch port.	16
2. Connect the end of the adapter into the DC power supply socket located on the back of the device.	16
3. Plug the AC adapter into a power outlet. After approximately 30 seconds, the unit powers up automatically as indicated by a steady green LED illuminated on the power button.	16
Step 2: Access WD ShareSpace on the Network	17
Using WD Discovery (Windows only)	17
1. Turn on your computer and wait for the operating system to load.	17
2. Insert the software-installing CD into the CD or DVD ROM drive.	17
3. Windows Vista/Windows 7: Click Run setup.exe, and then click Allow.	17
4. Click Accept in the Terms of Agreement screen.	17
5. If you have connected the WD ShareSpace properly as shown in the Connect screen on page 13, click Next.	18
6. The Application Installer screen opens, displaying a list of options. Click WD Discovery Tool. Once the WD Discovery Tool installation is complete, it automatically launches and the WD Discovery icon displays on your desktop.	18
7. The WD Discovery screen appears. Click WDShareSpace in the Network Drives Found list and click Configure.	18
8. The login screen appears. Continue device setup by following the instructions for “Setting Up the Device for the First Time” on page 89.	19
Using Windows Network and Sharing Center	19
1. For Windows Vista/Windows 7, click Start>Computer>Network.	19
2. Right-click WDShareSpace in the Network and Sharing center and select Install from the drop-down menu.	19
3. Click Locate and install driver software (recommended).	20
4. Click Yes, always search online (recommended).	20
5. When installation is complete, a confirmation message displays. Click Close.	20
To open the WD ShareSpace shares:	21
1. Right-click WDShareSpace and select Open from the drop-down menu.	21
2. To view the contents, enter your username and password (“admin” is the default for both) and click OK. The Public, Configuration, and Download shares (default shares) display.	22
To create a desktop shortcut to the WD:	22
To view the WD ShareSpace web page:	22
To view the properties of the WD ShareSpace:	23
1. Right-click WDShareSpace and select Properties from the drop-down menu.	23
2. Click OK to close the screen.	23
Mac OS X Leopard/Snow Leopard	23
1. Turn on your computer and wait for the operating system to load.	23
2. In Finder, double-click WDShareSpace in the Shared list (if necessary, click All then double-click WDShareSpace).	23
3. On the login page, type “admin” in both the Name and Password fields and make sure the Remember this password in my keychain check box is selected. Click Connect.	23
4. Double-click the Public icon to display the subfolders: Shared Music, Shared Pictures, and Shared Videos.	24
5. If you want to make the shared drive icon permanent on your desktop, create an alias. Following are two ways to do that:	24
Mac OS X Tiger	25
1. Turn on your computer and wait for the operating system to load.	25
2. Open Finder. Click Network and then double-click the WDShareSpace icon.	25
3. Type “admin” in both the Name and Password fields, and make sure the Remember this password in my keychain check box is selected. Click Connect.	25
4. Make sure that Public is highlighted in the Select the volumes to mount list, and then click OK.	26
5. Double-click the Public icon that is now on your desktop to display three shared subfolders. You can now drag and drop files into the shared folders using Finder.	26
6. If you want to make the shared drive icon permanent on the desktop, create an alias. Following are two ways to create to do that:	26
Backing Up Computers on a Network	28
WD Anywhere Backup Overview	28
Important Installation Notes	28
Windows	28
1. Turn on your computer and wait for the operating system to load.	28
2. Insert the software CD into the CD-ROM drive.	28
3. Windows Vista/Windows 7: Click Run setup.exe and then click Allow.	28
4. Click Accept in the Terms of Agreement screen.	28
5. If you have connected the device properly as shown in the Connect screen on page 13, click Next.	28
6. Click WD Anywhere Backup.	28
7. Select your preferred language from the list and click OK.	29
8. Close all other open applications, and then click Next to continue.	29
9. If you accept the terms of the agreement, click I Agree to continue.	29
10. Continue with “One-Click Backup” on page 28 or “Creating a Customized Backup Plan” on page 32.	30
Mac OS X	31
1. Turn on your computer and wait for the operating system to load.	31
2. Double-click the WD ShareSpace icon on the desktop.	31
3. Double-click WD_Anywhere_Backup.dmg.	31
4. On the WD Anywhere Backup screen, click the WD Anywhere Backup icon.	31
5. On the verification dialog box, click Continue.	31
6. On the Welcome screen of the Install WD Anywhere Backup wizard, click Continue.	32
7. On the Software License Agreement screen, click Continue.	32
8. To accept the software license agreement, click Agree.	32
9. Click Install.	32
10. Enter your Mac user name and password.	32
11. When a screen verifying successful installation appears, click Close.	33
12. Now you can begin backing up your data.	33
Configuring WD Anywhere Backup	33
One-Click Backup	33
To start an automatic and complete backup of your computer’s hard drive:	34
1. Click Back Up All of My Files.	34
2. A message explains that initial backup will use moderate resources on your computer. To pause the backup, click Pause until System Idle. To keep the backup running in the background, click Continue.	34
3. A registration screen appears. If desired, enter the optional registration information. Click Continue. The WD Anywhere Backup screen displays the progress of the backup and percentage of CPU used (bottom right of screen).	35
To customize a backup plan:	36
1. Click the Customize My Backup link at the bottom right of the WD Anywhere Backup Configuration screen. The Welcome to the WD Anywhere Backup Wizard screen appears.	36
2. Continue with step 3 in “Creating a Customized Backup Plan” on page 32.	36
Creating a Customized Backup Plan	37
1. If WD Anywhere Backup is not already running, click the WD Anywhere Backup icon on the desktop.	37
2. Click Create. (If the screen shows no backup plans, none has been created.)	37
3. The welcome screen for customizing your backup appears. Click Next.	37
4. Click Network Places and locate your WD ShareSpace on your local area network. Click Next.	38
Selecting all items from SmartPicks	39
1. Click the All Items from SmartPicks button. The SmartPicks screen displays, listing common file types that you can back up.	39
2. Select each file type you want to back up. You can also click Select None to clear all selections, or click Select All to select all of the items.	39
3. To add more items, click the Add Backup Items button. The Local Folders tab displays. Select additional folders and click Select.	39
4. To exclude more items from your plan:	40
(a) Click the Show Advanced Options button.	40
5. On the Items Selected for Backup screen, click Next.	40
6. Continue with “Completing the Backup Plan” on page 37.	40
Selecting your own backup items	41
1. Click the My Own Backup Items button. The SmartPicks screen appears, listing default file locations you can back up.	41
2. You have two options:	41
(a) On the SmartPicks tab, select each item you want to back up. You can also click Select None to clear all selections, or click Select All to select all of the items. When finished, click Next.	41
3. On the Items Selected for Backup screen, you can add more items or use advanced items as described in “Selecting all items from SmartPicks” on page 34.	42
4. On the Items Selected for Backup screen, click Next.	42
5. Continue with Completing the Backup Plan below.	42
1. Name your backup plan and click Next. You can create additional backup plans by repeating the steps above.	42
2. A confirmation screen appears. Click Done.	43
3. A message explains that initial backup will use moderate resources on your computer. To pause the backup, click the Pause until System Idle link.	43
4. To keep the backup running in the background, click Continue.	43
Restoring a Backup Plan	45
1. Click View and Restore.	45
2. Click a backup plan in the Select a Plan list, or to search for a backup plan, enter the name in the Search by File Name field and click Search.	45
3. Click the box next to the folders or files you want to restore.	45
4. From the Restore Files to list, select a location for your restored files and click the Restore button.	45
Reactivating a Backup Plan	46
1. On the menu bar, click Actions>Reactivate Backup Plan.	46
2. The Reactivate wizard appears. Click Next.	46
3. Browse to select the location of the backup folder and click Next.	46
4. If you have more than one backup plan, select the one you want to reactivate and click OK.	46
5. Select the No, just reactivate the backup plan and start backing up option and click the Next button. Your backup plan will be reactivated, and your computer will back up files onto your selected backup destination.	46
Editing a Backup Plan	47
1. On the WD Anywhere Backup screen, click the Change Selected Files icon. (See “Icons” on page 42.) The WD Anywhere Backup Configuration screen appears.	48
2. Do one of the following:	48
3. When you finish selecting items to add or remove, click the Select (or OK, depending on the screen) button.	48
4. When returned to the WD Anywhere Backup Configuration screen, click the Done button.	48
1. Click the Change Selected Settings icon. (See “Icons” on page 42.) Select the Keep up to check box and enter the maximum number of earlier versions of your files to back up.	49
2. Click OK.	49
1. Click the Remove Backup Plan icon. (See “Icons” on page 42.)	49
2. In response to the confirmation message, click OK.	49
1. Select the backup plan, and click the Show Backup Log icon. (See “Icons” on page 42.) The Backup Log appears.	49
2. To view the error log, click the Error Log tab.	50
3. To see an explanation of an error in the list displayed in the lower part of the screen, click the error.	50
4. To clear selected errors, select their check boxes and click the Clear Selected Errors button.	50
5. To clear all errors, click the Clear All Errors button.	50
6. To prevent the Error Log from displaying transient errors, click the Do not notify me about transient errors check box. This selection affects all backup plans.	50
7. To see which files have been backed up, click the click here to launch the WD Anywhere Restore application link. (For information on restoring, see “Restoring a Backup Plan” on page 40.)	50
Using Time Machine™	51
Setting up Time Machine	51
1. Use one of the following methods to open Time Machine.	51
2. If this is your first time creating a backup, the following screen displays:	51
3. Click the Choose Backup Disk button and select the WD ShareSpace drive where you want the backups stored.	52
4. Click the Use for Backup button. A screen prompts you for your user name and password. Enter wd_backup as the user name and backup as the password (not case-sensitive).	52
5. Click the Connect button. The Preferences screen returns.	52
6. To start automatic backups, move the slider to ON.	52
7. To add a Time Machine drop-down menu to the menu bar at the top of the screen, select the Show the Time Machine status in the menu bar check box. This menu enables you to start a backup, enter Time Machine to restore files, or open the Time Machin...	53
Starting a Backup	54
Restoring Backed-up Items	54
1. Open the window on your computer where you want the item restored. For example, if you are restoring a document, open the Documents folder. (If you are restoring an item on your desktop, you do not need to open a window.)	54
2. Click the Time Machine icon in the Dock or select Enter Time Machine from the drop-down menu.	54
3. Click the arrows or the time line on the right of the screen to browse through all the backups Time Machine has created.	55
4. Select the item you want to restore, and click the Restore button to display the following options:	55
5. Click the button for the desired option:	55
Deleting the Entire Backup	56
1. In Finder, select the WD ShareSpace drive and click the Connect As button.	56
2. Enter wd_backup as the user name and backup as the password (not case- sensitive) and click Connect.	56
3. Select the backup folder and then drag the *.sparsebundle file to the Trash icon.	57
Changing Your Password	57
1. Log in to the WD ShareSpace web user interface. (See “Accessing WD ShareSpace’s Network Storage Manager” on page 92.)	57
2. Enter your username and password and click Login (default username and password are “admin”).	57
3. Click the Users button in Basic mode.	58
4. Click the icon to the right of the user name (WD_Backup).	58
5. When the Users page appears, enter your new password in the New and Confirm password fields and click Submit.	58
6. A confirmation message displays.	59
MioNet Remote Access	60
MioNet Overview	60
Remote Access Setup	60
Windows	60
1. Turn on your computer and wait for the operating system to load.	60
2. Insert the WD ShareSpace software CD into the CD-ROM drive.	60
3. Windows Vista/Windows 7: Click Run setup.exe and then Allow.	60
4. Click Accept in the Terms of Agreement screen.	60
5. If you have connected the device properly as shown in the Connect screen on page 13, click Next.	60
6. Click the MioNet New Account button if you are a new MioNet user; click MioNet - Existing Account if you are an existing user. The MioNet registration screen appears.	61
7. Complete the registration form and click Submit to create an account.	61
8. When MioNet finds the WD ShareSpace you are registering, enter a name for the device and click OK.	62
9. A confirmation message appears. Click OK.	62
Using MioNet Web (after registration)	63
1. From any browser, go to www.mionet.com/web and enter your username and password. The Quick Start tab appears, displaying icons representing activities you can perform.	63
Accessing WD ShareSpace Folders and Files Remotely	64
1. Click the My Resources tab to display your WD ShareSpace folders.	64
2. Select a folder to see a list of all the sub-folders and files. You can now use your browser to access your entire collection of music, photos, movies, and documents.	64
3. Double-click any file to open it locally. You may be able to drag and drop files from your WD ShareSpace to the remote computer and vice versa.	64
Sharing Files with Others	64
1. Click the Share Photos icon.	64
2. Choose any folder or the plus sign to choose a sub folder to share with someone else and click the Next button.	65
3. To share photos with MioNet users you have shared with in the past:	65
(a) Select the user(s) and click the Next button.	65
4. To add a new user to share with:	65
(a) Click the Invite new person button.	65
5. To find another MioNet user you have never shared with before:	65
(a) Click the Find MioNet user button.	66
6. From the list of users, select the user(s) you want to share with and click the Next button.	66
1. Click the Transfer Files to Others icon to open a dialog window showing your WD ShareSpace folders.	67
2. Click the + to navigate through your directory to highlight the folder you wish to transfer files from and click Next.	67
3. To transfer files back and forth with MioNet users you have shared with in the past:	68
(a) Select the user(s) and click the Next button.	68
4. To add a new user to transfer files to and from:	68
(a) Click the Invite new person button.	68
5. To find a MioNet user you have never shared with before:	68
(a) Click the Find MioNet user button.	68
6. From the list of users, select the user(s) you want to transfer files to and from. Click the Next button.	69
7. Select the permission level and click the Next button. If you want users to only transfer the files to themselves, give them the read permission. If you want to enable them to transfer files to you (or modify or delete your files), give them the r...	69
How to Play/Stream Video, Music & Photos	70
Media Servers Overview	70
Media Types Supported	70
Media Storage	71
How and Where to Add Media Content to the Shared Folders	71
1. Open the Internet Explorer.	71
2. Copy your music files to the Shared Music folder, which is under the Public folder on WD ShareSpace.	71
3. Follow the same process to place your videos and pictures into their respective Shared Pictures and Shared Video folders.	71
Media Devices	72
WD TV Live HD Media Player	72
1. Connect a WD ShareSpace to your LAN and power on the device.	72
2. Make sure the WD TV Live is connected to your TV and powered on.	72
3. Connect the WD TV Live to the LAN.	72
4. Navigate to Settings>Network setting>Network setup to choose the connection type.	72
5. Use the navigation buttons to select Wired and press Enter.	72
6. Select Automatic as the setup configuration option for DHCP or Manual for a static IP.	73
7. A confirmation screen displays your WD TV Live’s network information if connection to the LAN is successful. Press Enter.	73
8. Navigate to the Home screen, and select the icon for media content you wish to access. It can be Music , Video , or Photo .	73
9. Press / to select Network Shares or Media servers and press Enter.	73
10. Press / to select the WD ShareSpace and press Enter.	73
11. Supported content for the selected media type displays.	74
12. Select the content you wish to access, and then press Enter to start media playback.	74
Windows Media Player 11/12 (Windows Vista/Windows 7)	74
To stream media using Windows Media Player 11 or 12 Library:	74
1. Click Control Panel>Network and Sharing Center.	74
2. Click Customize.	74
3. Click Private, and then click Next.	75
4. Launch Windows Media Player (Start>All Programs>Windows Media Player).	75
5. Click Library>Media Sharing.	75
6. Click Find media that others are sharing, and then click OK.	76
7. Select a media type (Music, Pictures, or Video) and click PVConnect on WDShareSpace.	76
8. Double-click the media file you want to play.	76
Xbox 360	76
1. Ensure that your Xbox 360 and WD ShareSpace are powered on and connected to your local area network.	76
2. From the main Xbox user interface, scroll to the My Xbox screen	76
3. Use the Xbox 360 controller and scroll to the right until you see Video, Music and Picture Library options.	76
4. Select any one of these three options by pressing the A button on your controller. The Select Source screen displays.	76
5. Select the WD ShareSpace option based on the device name you created previously and press the A button. You see the media content stored on your WD ShareSpace unit.	76
PlayStation 3	77
1. Ensure that your PlayStation 3 and WD ShareSpace are powered on and connected to your local area network. You will see the main user interface with a series of options displayed horizontally across your TV screen.	77
2. Using the directional buttons (left and right) on the PlayStation controller, navigate to Music, Photo or Video depending on which type of media you want to play, and press the X button.	77
3. Using the directional buttons (up and down), scroll and select WDShareSpace (or the new device name that you created previously) by pressing the X button. You will now see a list of folders (Music, Photo and Video) to the right of the WDShareSpace...	77
4. Make sure that you select the folder that corresponds to the option you selected back in Step 2. For example, if you select Photo from the main user interface screen, open the corresponding Photo folder to the right of the WDShareSpace icon, other...	77
Digital Picture Frames	77
1. Ensure that your WD ShareSpace is connected to your home’s local network and is powered on.	77
2. Follow the user instructions provided with your wireless digital photo frame to proceed through any initial setup or installation of drivers.	77
3. Using the navigation feature on your wireless digital photo frame, scan and detect the WD ShareSpace on your network.	77
4. Depending on the brand of photo frame you have, you may need to access Settings/Network Setup screen in the user interface to establish connection so that your photo frame can link to your WD ShareSpace. Please refer to the user guide for your Dig...	77
5. Once you have a connection between your wireless photo frame and the WD ShareSpace, access the Media screen on your photo frame that will provide you the option to view your pictures.	77
Network Music Player	78
1. Connect WD ShareSpace to your local area network and power on the device.	78
2. Connect and configure your network music player on your home’s wired or wireless network switch or router.	78
3. Turn on your network music player.	78
4. If connected properly, you will find the device name of your WD ShareSpace.	78
5. Navigate through the network music player’s user interface to locate and play music stored on your WD ShareSpace.	78
Digital Media Adapters	78
1. Connect WD ShareSpace to your local area network and power on the device.	78
2. Make sure that your DMA device is connected to your TV and powered on. The main screen of your DMA device appears.	78
3. Depending on the DMA device, you may need to access the Settings/Network Setup screen in the user interface to establish a connection between your DMA and WD ShareSpace. Please refer to your DMA’s user guide for specific instructions.	78
4. Once you have a connection established between your DMA and WD ShareSpace, access the Media screen on your DMA to view your pictures or stream music and video content from the WD ShareSpace.	78
DLNA® Devices	78
iTunes with WD ShareSpace	79
iTunes Media Server Overview	79
Media Types Supported	79
Storing Content	79
Streaming Audio in iTunes	79
1. Launch iTunes on your computer.	79
2. Click WDShareSpace under the Shared section of the left pane. If you have copied music to the /Public/Shared Music folder and it is in a format supported by iTunes, it should be listed in the right pane.	79
3. Double-click an audio file to play.	80
External USB Drive Sharing & Backup	81
Sharing Data on a USB Drive	81
To share data on a USB drive:	81
1. Connect a USB drive to any of the three USB ports. The front port is USB1 and the two rear ports are USB2 and USB3 from top to bottom.	81
2. Open the WDShareSpace folder to access data on the USB drive. Double-click the USB share. The USB share name will appear as usb1-1share1, usb2-1share1, or usb3-1share1, depending on the actual USB port that the USB drive is connected to.	81
USB Auto Backup Feature	81
To back up FROM a USB drive:	82
1. Connect a USB drive to the USB port (Port 1) located on the front panel, and wait for a few seconds for the USB backup LED on the front of the unit to light steadily (this could take up to 30 seconds).	82
2. Press and hold the USB backup button only until the USB backup LED turns off (about 2 seconds). While the backup is in progress, the USB LED will flash once per second. When the backup is complete, the LED will remain on steadily.	82
To back up t o a USB drive:	83
1. Prior to performing the backup operation, make sure to choose a source and destination in the WD ShareSpace’s Network Storage Manager utility. See “To set a source share name for WD ShareSpace to USB drive backup:” on page 145 for more infor...	83
2. Connect a USB drive to the USB port (Port 1) located on the front panel of the WD ShareSpace, and wait for the USB backup LED to turn on (about 30 seconds).	83
3. Press and hold the USB backup button until the USB backup LED on the front of the unit begins to flash (about 3 seconds). The USB LED will flash twice per second while the backup is in progress and will light steadily when the backup is complete.	83
Using WD Discovery (Windows Only)	84
WD Discovery Overview	84
Mapping a Network Drive	84
To map a network drive:	84
1. Turn on your computer and wait for the operating system to load.	84
2. If WD Discovery is not running:	84
3. Click the device you want to map in the Network Drives Found list and click Map Network Drive in the Things to Do list.	85
4. In the authentication screen, enter your User Name and Password. The default for both is “admin.”	85
1. After completing step 4 on the previous page, click Yes. All share folders available on the device will be mapped as network drives automatically. Available drive letters are assigned backwards from Z. When mapping completes, the share folders app...	86
2. Click Back to return to the main screen.	86
1. After completing step 4 on the previous page, click No. All share folders on the device are listed on the screen. Select a folder name, and then select a drive letter.	86
2. Click Yes to complete drive letter assignment.	86
3. Click My Computer (Computer on Windows Vista/Windows 7). The network drives display. You can now drag and drop files into the network drive folders using My Computer or Windows Explorer.	86
Browse Network Shares	87
To access data on a share using WD Discovery:	87
1. Ensure that the device is powered on and connected to the network.	87
2. Launch WD Discovery from the Start menu or the desktop.	87
3. Click WDShareSpace in the Network Drives Found list and click Browse Network Shares in the Things To Do list.	87
4. After successful login, the share folders on the device are listed. Click a share to view and access share files in Windows Explorer.	87
5. Copy your music files into the Shared Music folder, your video files into the Shared Videos folder, and your photos and pictures into the Shared Pictures folder.	88
Desktop Shortcut Creation	88
1. Ensure that the device is powered on and connected to the network.	88
2. Launch WD Discovery from the Start menu or the desktop.	88
3. Click WDShareSpace in the Network Drives Found list, and then click Create Desktop Shortcut in the Things To Do list.	88
4. A dialog appears informing you that the desktop shortcut has been created successfully. Click OK.	89
Turning Identify LED On or Off	89
To turn on the Identify LED on a networked WD ShareSpace:	89
1. Ensure that the device is powered on and connected to the network.	89
2. For Windows 2000/XP, click Start>All Programs>WD Discovery Software>WD Discovery, or double-click the WD Discovery icon on your desktop.	89
3. Click WDShareSpace in the Network Drives Found list and click Turn On Identify LED in the Things To Do list.	89
4. The Identify LED on the target device is turned on. The LED icon appears to the left of the device name in WD Discovery.	90
To turn off the Identify LED on a remote networked WD ShareSpace device:	90
1. Ensure that the device is powered on and connected to the network.	90
2. Click Start>Programs>WD Discovery.	90
3. Click WDShareSpace in the Network Drives Found list and click Turn Off Identify LED in the Things To Do list.	90
Automatically Updating WD Discovery	90
To download the update:	91
1. On the WD Discovery Auto Update Progress screen, click Yes.	91
2. To launch WD Discovery, click Yes.	91
Network Storage Manager: Basics	92
Configuring WD ShareSpace	92
Windows	92
To configure your WD ShareSpace for Windows:	92
1. Turn on your computer and wait for the operating system to load.	92
2. Insert the WD ShareSpace software CD into the CD-ROM drive.	92
3. Windows Vista/Windows 7: Click Run setup.exe, and then click Allow.	92
4. Click Accept in the Terms of Agreement screen.	92
5. If you have connected the device properly as shown in the Connect screen on page 13, click Next.	92
6. The Application Installer screen opens, displaying a list of options. Click WD Discovery Tool.	92
7. The WD Discovery screen appears. Click WDShareSpace in the Network Drives Found list and click Configure.	93
8. The login screen appears. Continue device setup by following the instructions for “Setting Up the Device for the First Time” on page 89.	93
Mac OS X	93
To configure the WD ShareSpace for Mac OS X:	93
1. Turn on your computer and wait for the operating system to load.	93
2. Open the Safari web browser.	93
3. Click the Bookmarks linkin the upper left corner of the screen.	93
4. Click Bonjour, and then double-click WDShareSpace.	93
5. The login screen appears.	93
6. Continue device setup by following the instructions for “Setting Up the Device for the First Time” on page 89.	93
Setting Up the Device for the First Time	94
1. Enter “admin” in both the Administrator Name and Password fields.	94
2. Select a language from the Language list and click Login.	94
3. Click Next.	94
4. Read the license agreement, and then click I Agree.	95
5. In the Initial Setup screen, do the following:	95
(a) Enter a name in the Device Name field (up to 15 characters, including alphanumeric and dash ‘-’).	95
6. Enter a new admin password in the New Admin Password field. The maximum length of the password is 16, including alphabetic, numeric, underscore, space, and most special characters except double-quote (\	96
7. Retype the new password in the Confirm Password field. Click Next.	96
8. Accept the default DHCP (Dynamic Host Configuration Protocol) client settings. If you are not using DHCP, click Static and manually assign the IP address. Click Next.	96
9. The Summary screen appears. Click Finish.	97
Accessing WD ShareSpace’s Network Storage Manager	97
Windows	98
1. Ensure that the device is powered on and connected to the network.	98
2. If WD Discovery is not running, launch it from the Start menu or the desktop.	98
3. Click WDShareSpace in the Network Drives Found list and point to and click Configure in the Things To Do list.	98
4. The login page appears. Type in the administrator name and password (the default password is “admin” unless it has already been changed by the administrator). In the Tool list, click WD ShareSpace’s Network Storage Manager. In the Language l...	98
Mac OS X	98
1. Turn on your computer and wait for the operating system to load.	98
2. Open the Safari web browser.	98
3. Click the Bookmarks linkin the upper left corner of the screen.	98
4. Click Bonjour, and then double-click WDShareSpace.	98
5. The login page appears. Type in the administrator name and password. In the Tool list, click WD ShareSpace’s Network Storage Manager. In the Language list, click the language for your region. Click Login.	98
WD ShareSpace’s Network Storage Manager Features	99
User Interface Overview	100
Toolbar	101
Basic Mode	101
Device Name	102
1. Click the Device Name button in Basic Mode home page.	102
2. Enter or change the text in the Device Name and/or Device Description fields.	102
3. Click Submit.	102
Date & Time	103
1. Click the Date & Time button on the Basic Mode home page.	103
2. Deselect Enable to set the time manually.	103
3. To synchronize the date and time automatically, click Enable.	103
4. Click Submit.	103
Network	104
To configure the network settings:	104
1. Click the Network button on the Basic Mode home page.	104
2. In the Network Mode drop-down menu, select a network mode. Selecting DHCP Client as a network mode causes the device to obtain an IP address automatically from the local DHCP server. Selecting Static IP as a network mode requires you to enter IP i...	104
3. Click Submit.	104
Users	104
To create a new user account:	106
1. Click the Users button on the Basic Mode home page.	106
2. Click the Add icon .	106
3. Enter the user name in the User Name field.	106
4. Enter the user’s full name in the Full Name field.	106
5. Enter the password in the Password field.	106
6. Re-enter the password in the Confirm Password field.	106
7. Create a private user share at the same time by clicking Yes next to Create User Private Share. The new user is granted full access to the private share. The private share name is the same as the user name.	106
8. Click Submit.	106
To change a user password:	106
1. Click the Users button on the Basic Mode home page.	106
2. Click the Change Password icon next to the appropriate user account.	106
3. Make the necessary changes, and then click Submit.	106
To delete an existing user account:	106
1. Click the Users button on the Basic Mode home page.	106
2. Select the user account you want to delete, and then click the Delete icon .	106
3. Click OK.	106
Folder Shares	107
To create a share:	108
1. Click Folder Shares on the Basic mode home page.	108
2. Click the Add icon .	108
3. Enter a share name in the Share field. The share name can contain up to 32 characters, including alphabetic, numeric, or underscore characters.	108
4. Enter a brief description in the Description field.	108
5. Click Submit.	109
To delete existing shares:	109
1. Select the share to delete.	109
2. Click the Delete icon .	109
3. Click OK.	109
System Status	109
Remote Access	110
To register with MioNet:	111
1. Click the Create MioNet account link in the note at the bottom of the page. The MioNet web registration page displays.	111
2. Enter the registration information required and click Submit.	111
To log in to an existing MioNet account:	111
1. Click the MioNet login link at the bottom of the page.	111
2. Enter your MioNet username and password and click Go.	111
Shutdown/Reboot	112
To shut down the WD ShareSpace:	112
1. Click Shutdown/Reboot on the Basic mode home page.	112
2. On the Shutdown/Reboot page, click Shutdown.	112
3. Click OK.	112
To reboot the WD ShareSpace:	112
1. Click the Shutdown/Reboot button on the Basic Mode home page.	112
2. On the Shutdown/Reboot page, click Reboot.	112
3. Click OK.	112
Network Storage Manager: Advanced Mode	113
System Tab	114
General Setup	114
To configure system general setup settings:	115
1. Assign a device name for this storage device in the Device Name field. The device name can contain up to 15 characters, including alphabetic, numeric, and hyphens only.	115
2. Enter a brief description for this storage device in the Device Description field. The maximum length of the description must not be more than 256 alphanumeric characters.	115
3. For Web Access Protocol, select either of the following web access protocols:	115
4. To set the date and time manually, deselect Enable next to NTP Service.	115
5. Select a time zone from the Time Zone list.	115
6. Adjust the date and time manually in the Date & Time lists.	115
7. Click Submit.	115
Alerts Setup	116
To set up automatic email notifications:	117
1. On the Alerts Setup page on the System tab, click Enable next to Email Notification. The page displays additional fields.	117
2. In the SMTP Server field, enter the name or IP address of the SMTP server used for email. (Check with your Internet Service Provider (ISP) for the SMTP server settings, which may include the SMTP port, and ask whether to enable TLS/SSL or SMTP aut...	117
3. In the Email Return Path field, enter a valid return email address recognized by your ISP. For example, if your SMTP server is \	117
4. In the Email Recipients field, enter the email address where you want to send an email message when an event occurs. Up to five email addresses can be used at a time.	117
5. Click Send Test Mail to send a test alert and confirm your settings are correct. A test message will be sent to each entered email address.	117
6. Click Submit.	117
To configure alerts to send pop-up messages when an event occurs:	118
1. On the Alerts Setup page on the System tab home page, click Enable next to Pop-Up Notification.	118
2. Enter the name of the computer in the Notified Devices field. When an event occurs, a pop-up message will appear on the computer. Up to five computer names can be added to the alert list.	118
3. Click Send Test Pop-up to send a test alert and confirm that the settings are correct.	118
4. Click Submit.	118
Admin Password	119
To change the administrator's password:	119
1. Click the Admin Password button on the System tab home page.	119
2. In the Old Password field, enter the old password.	119
3. In the New Password field, enter the new password. The maximum length of the password is 16, including alphabetic, numeric, underscore, space, and most special characters except double-quote (\	119
4. In the Confirm Password field, re-enter the new password.	119
5. Click Submit.	119
Update (Firmware)	119
1. Click the Update button on the System tab home page.	119
2. Click Check For New Firmware.	120
3. Click Download if new firmware is available.	120
4. Click Upgrade. Wait for the update process to complete.	120
1. Before attempting a manual update, check support.wdc.com for firmware availability.	121
2. If a new firmware file is available, obtain it from WD Technical Support at support.wdc.com.	121
3. Save the file to a Desktop location on your computer.	121
4. Click the Manual tab on the Update page.	121
5. Under Firmware Update, click the Browse button and locate the firmware file you saved.	121
6. Click Submit.	121
7. After your firmware has been updated, the device will reboot. The web user interface redirects to the System Status page after the update is completed.	121
Configuration	123
To back up the current system configuration settings:	123
1. On the Configuration page, click Save Current Configuration.	123
2. Click Save.	123
3. Specify a file name and location for saving the file.	123
4. Click Save.	123