Whirlpool GU3100XTVQ Installation Instructions - Page 3

INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools Needed ■ Phillips screwdriver ■ Flat-blade screwdriver and ¼" nut drivers ■ Measuring tape or ruler and 1½" (1.3 mm, 1.9 mm and 3.8 cm) hole saw bits ■ Twist-on wire connectors (proper size to connect household wiring to 16-gauge wiring in dishwasher) (2) ■ 6" (15.2 cm) adjustable wrench ■ Small tubing cutter ■ Level ■ Cordless drill drill bit ■ Flashlight ■ Shallow pan ■ Wood block ■ Bath towel ■ This dishwasher is manufactured for indoor use only. ■ Do not run drain lines, water lines or electrical wiring where they can interfere with or contact the dishwasher motor or legs. ■ The location where the dishwasher will be installed must provide clearance between motor and flooring. Motor should not touch the floor. ■ Do not install dishwasher over carpeted flooring. Minimum Clearances Check location where the dishwasher will be installed. the location must provide: ■ Easy access to water, electricity and drain. ■ Convenient access for loading and unloading dishes. Corner locations require 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet. ■ A minimum of 25⁵⁄₈" (65.1 cm) is required in front of the dishwasher to allow the door to open fully. Parts Needed ■ 90º elbow with ³⁄₈" N.P.T. external threads on one end NOTE: The other end must fit the water supply line. ■ Thread seal tape ■ 3 UL listed wire nuts ■ Copper tubing (³⁄₈" recommended) ■ 1¹⁄₂" to 2" (3.8 cm to 5.1 cm) screw-type clamp ■ Clamp connector to fit 22.2 cm) diameter hole ■ 1¹⁄₂" to 2" (3.8 cm to 5.1 cm) screw-type clamp if connecting to waste-tee C B A D Parts Supplied Check that all parts are included. See separate parts list for accessories available for your dishwasher. A B A. #8 x ⁵⁄₈" Phillips flat-head wood screws B. Phillips color-matched toekick screws Location Requirements IMPORTANT: Observe all governing codes and ordinances. Failure to meet codes and ordinances could lead to fire or electrical shock. Proper installation is your responsibility. ■ Contact a qualified installer to ensure that the dishwasher is installed to meet all electrical and plumbing national and local codes and ordinances. ■ Install the dishwasher as specified in these instructions. ■ Have everything you need to properly install dishwasher. ■ Shelter dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty. A. 2" (5.1 cm) minimum clearance for door opening B. Dishwasher C. Countertop D. 25⁵⁄₈" (65.1 cm) minimum ■ Square opening for proper orientation. ■ Cabinet front perpendicular to floor. ■ Level floor. If the floor at the front of the dishwasher is not level with the rear of the opening, shims may be needed to level the dishwasher. NOTE: To avoid shifting during dishwasher operation, shims must be securely attached attached to the floor. If the dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel. Make sure pipes, wires and drain hose are within the shaded area shown in the "Cutout dimensions" section. Helpful Tip: If the floor in the dishwasher opening is uneven (example: tile flooring only partway into opening) you will need to be accurate when measuring the dimensions and in leveling the dishwasher. 3