Home » Whirlpool Manuals » Laundry Dryers » Whirlpool WED6600WL » Manual Viewer

Whirlpool WED6600WL Use and Care Guide - Page 11

wire connection: Power supply cor, wire connection: Direct Wire

UPC - 883049178431

View all Whirlpool WED6600WL manuals

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

3. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw. A E B C F D 2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw. A C B D E A. External ground conductor screw B. Neutral ground wire C. Ground wire (green or bare) of power supply cord D. ¾" (19 mm) UL listed strain relief E. Center, silver-colored terminal block screw F. Neutral wire (white or center wire) 4. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. A. External ground conductor screw B. Neutral ground wire C. Center, silver-colored terminal block screw D. Neutral wire (white or center wire) E. ¾" (19 mm) UL listed strain relief 3. Connect the other wires to outer terminal block screws. Tighten screws. 5. Tighten strain relief screw. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. Now go to "Venting Requirements." 3-wire connection: Power supply cord Use where local codes permit connecting cabinet-ground conductor to neutral wire. B D E A C GF A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Neutral prong D. Spade terminals with upturned ends E. 3/4" (19 mm) UL listed strain relief F. Ring terminals G. Neutral wire (white or center wire) 1. Loosen or remove center, silver-colored terminal block screw. 4. Tighten strain relief screws. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. You have completed your electrical connection. Now go to "Venting Requirements." 3-wire connection: Direct Wire Use where local codes permit connecting cabinet-ground conductor to neutral wire. Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed. Strip 31/2" (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into a hook shape. (215"mm) 3½" (89 mm) 11

Section	Page
cabrio® steam fabric care system ELECTRIC DRYER	1
Use & Care Guide	1
For questions about features, operation/performance, parts, accessories or service call: 1-800-253-1301	1
In Canada, call: 1-800-807-6777 or visit our website at www.whirlpool.com or www.whirlpool.ca	1
Sécheuse électrique Cabrio® avec système de soin des tissus	1
Guide d’utilisation et d’entretien	1
Au Canada, pour assistance, installation ou service, composez le : 1-800-807-6777 ou visitez notre site internet à www.whirlpool.ca	1
Table of Contents/Table des matières 2	1
table of contents	2
Table des matières	2
dryer Safety	3
INSTALLATION instructions	4
Tools and Parts	4
Parts supplied:	4
Parts needed:	5
If using a power supply cord:	5
Location Requirements	5
You will need	5
Installation Clearances	5
Dryer Dimensions	5
Installation spacing for recessed area or closet installation	5
Mobile home - Additional installation requirements	5
Mobile home installations require:	6
Electrical Requirements - U.S.A. Only	6
It is your responsibility	6
Electrical Connection	6
If using a power supply cord:	6
If your outlet looks like this:	6
4-wire receptacle (14-30R)	6
If your outlet looks like this:	6
3-wire receptacle (10-30R)	6
If connecting by direct wire:	6
Electrical Requirements - Canada Only	7
It is your responsibility	7
4-wire receptacle 14-30R	7
Electrical Connection - U.S.A. Only	8
Power Supply Cord	8
Direct Wire	8
1. Disconnect power.	8
2. Remove the hold-down screw and terminal block cover.	8
3. Install strain relief.	8
4. Now complete installation following instructions for your type of electrical connection:	9
Electrical Connection Options	9
If your home has:	9
And you will be connecting to:	9
Go to Section:	9
4-wire connection: Power supply cord	9
1. Remove center, silver-colored terminal block screw.	9
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.	10
3. Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.	10
4. Connect the other wires to outer terminal block screws. Tighten screws.	10
5. Tighten strain relief screws.	10
6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	10
7. You have completed your electrical connection. Now go to “Venting Requirements.”	10
4-wire connection: Direct Wire	10
1. Remove center, silver-colored terminal block screw.	10
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block....	10
3. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.	11
4. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.	11
5. Tighten strain relief screw.	11
6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	11
7. You have completed your electrical connection. Now go to “Venting Requirements.”	11
3-wire connection: Power supply cord	11
Use where local codes permit connecting cabinet-ground conductor to neutral wire.	11
1. Loosen or remove center, silver-colored terminal block screw.	11
2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.	11
3. Connect the other wires to outer terminal block screws. Tighten screws.	11
4. Tighten strain relief screws.	11
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	11
6. You have completed your electrical connection. Now go to “Venting Requirements.”	11
3-wire connection: Direct Wire	11
Use where local codes permit connecting cabinet-ground conductor to neutral wire.	11
1. Loosen or remove center, silver-colored terminal block screw.	12
2. Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.	12
3. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.	12
4. Tighten strain relief screw.	12
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	12
6. You have completed your electrical connection. Now go to “Venting Requirements.”	12
Optional 3-wire connection	12
Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.	12
1. Remove center, silver-colored terminal block screw.	12
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver- colored terminal block screw. Tighten screw.	12
3. Connect the other wires to outer terminal block screws. Tighten screws.	12
4. Tighten strain relief screws.	12
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	12
6. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.	12
Venting Requirements	13
If using an existing vent system	13
If this is a new vent system	13
Vent material	13
Rigid metal vent	13
Flexible metal vent	13
Elbows	13
Good	13
Better	13
Clamps	13
Exhaust	13
Plan Vent System	14
Choose your exhaust installation type	14
Recommended exhaust installations	14
Standard exhaust installation with rigid metal or flexible metal vent	14
Alternate installations for close clearances	14
Special provisions for mobile home installations	14
Determine vent path	14
Determine vent length and elbows needed for best drying performance	15
Vent system chart	15
Number of 90º turns or elbows	15
Type of vent	15
Box or Louvered hoods	15
Angled hoods	15
0	15
Rigid metal	15
1	15
Rigid metal	15
2	15
Rigid metal	15
3	15
Rigid metal	15
4	15
Rigid metal	15
Install Vent System	15
1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.	15
2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4\	15
3. Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into the ...	15
Install Leveling Legs	15
1. To avoid damaging the floor, use a large, flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.	15
2. Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on the cardboard. See illustration.	15
3. Examine the leveling legs. Find the diamond marking.	15
4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.	15
5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.	15
Connect Vent	15
1. Using a 4\	15
2. Move dryer into its final location. Do not crush or kink vent.	15
3. Once the exhaust vent connection is made, remove the corner posts and cardboard.	15
Connect Inlet Hose	15
1. Turn cold water faucet off and remove washer inlet hose.	15
2. Remove old rubber washer from inlet hose and replace with new rubber washer provided. If space permits, attach the brass female end of the “Y” connector to the cold water faucet.	15
3. Attach short hose to cold water faucet. Screw on coupling by hand until it is seated on faucet.	15
4. Using pliers, tighten the couplings with an additional two-thirds turn.	15
5. Attach “Y” connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector.	15
6. One end of the long hose has a wire mesh strainer inside the coupling. Attach this end to the “Y” connector.	15
7. Attach washer cold inlet hose to other end of “Y” connector. Screw on coupling by hand until it is seated on connector.	15
8. Using pliers, tighten the couplings with an additional two-thirds turn.	16
9. Attach other end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector.	16
10. Using pliers, tighten the coupling with an additional two-thirds turn.	16
11. Check that the water faucets are on.	16
12. Check for leaks around “Y” connector, faucet, and hoses.	16
Level Dryer	16
Reverse Door Swing	16
1. Place a towel or soft cloth on top of the dryer or work space to avoid damaging the surface.	16
Remove the door assembly	16
1. Open the dryer door.	16
2. Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front panel of the dryer.	16
3. Loosen the top screw from each of the 2 hinges in Step 2.	16
4. Remove the dryer door and the hinges by lifting upward on the door. Lay the door on a flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose screws from dryer front panel.	16
5. Remove the 4 plastic plugs located outside the dryer door opening.	17
6. Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in Step 4.	17
Reverse the strike	17
1. Remove the door strike from the dryer door opening.	17
2. Remove the cosmetic screw opposite the door strike.	17
3. Reinstall the door strike and cosmetic screw on the opposite side of the dryer door opening from where they were removed. NOTE: Door strike and plugs must be on the same side of the dryer door opening.	17
Reinstall the door	17
1. Remove the 4 screws and 2 hinges from the dryer door.	17
2. Replace the 4 screws in the same holes.	17
3. Remove the 4 screws from the opposite side of the door.	17
4. Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge to the front panel.	17
5. Install screws in the top hinge holes in the door. Do not tighten screws. Leave approximately ¼\	17
6. Hang door by placing screw heads into top slotted holes of hinges and slide door down. Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge screws.	17
7. Close door to engage door strike.	17
Complete Installation	18
1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.	18
2. Check that you have all of your tools.	18
3. Dispose of/recycle all packaging materials.	18
4. Be sure the water faucets are on.	18
5. Check for leaks around “Y” connector, faucet, and hoses.	18
6. Check the dryer’s final location. Be sure the vent is not crushed or kinked.	18
7. Check that the dryer is level. See “Level Dryer.”	18
8. In the U.S.A.	18
9. Remove any film or tape remaining on the dryer.	18
10. Read “Dryer Use.”	18
11. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.	18
12. If you live in a hard water area, use of a water softener is recommended to control the buildup of scale through the water system in the dryer. Over time, the buildup of lime scale may clog different parts of the water system, which will reduce p...	18
13. Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this test, do not select the Air Only modifier.	18
Dryer Use	19
Starting Your Dryer	19
1. Clean lint screen before each load. See “Cleaning the Lint Screen.”	19
2. Place laundry into dryer and shut door.	19
3. Press POWER.	19
4. Turn the knob to the selected cycle. The preset settings for Automatic Cycles or Timed Cycles will illuminate. The estimated (automatic cycle) or actual (timed) cycle time (in minutes) will show in the display.	19
5. (OPTIONAL STEP) If desired, select OPTIONS. For more details, see “Options.”	20
6. (OPTIONAL STEP) If desired, press END OF CYCLE SIGNAL. A signal will sound to alert you when a cycle ends. For more details, see “End of Cycle Signal.”	20
7. Press START. Be sure the door is closed.	20
Stopping, Pausing, or Restarting	20
To stop or pause your dryer at any time	20
To restart the dryer	20
Drying and Cycle Tips	20
Drying tips	20
Cycle tips	21
Status Lights	21
Sensing	21
Wet	21
Damp	21
Cool Down	21
Done	21
WRINKLE SHIELD™ Setting	21
Indicator lights	21
Cycles	21
Automatic Cycles	21
Heavy Duty	21
Normal	21
Casual	21
Delicate	21
Automatic Preset Cycle Settings	21
Automatic Cycles Load Type	21
Temperature	21
Steam Cycles	22
Quick Refresh	22
Enhanced Touch Up	22
Steam Preset Cycle Settings	22
Timed Cycles Load Type	22
Default Temperature*	22
Default Time (Minutes)*	22
Timed Cycles	22
Timed Dry	22
Timed Preset Cycle Settings	22
Timed Cycle Load Type	22
Default Temperature	22
Default Time (Minutes)	22
Modifiers	22
Automatic Cycle Modifiers	22
Timed Cycle Modifiers	22
Air Only	23
Type of Load	23
Time* (Minutes)	23
When using Air Only	23
Options	23
Drum Light	23
WRINKLE SHIELD™ Setting	23
Damp Dry Signal	23
End of Cycle Signal	23
End of Cycle Signal	23
Changing Cycles, Modifiers, and Options	23
Changing Cycles after pressing Start	23
1. Press PAUSE/CANCEL twice.	23
2. Select the desired cycle and options.	23
3. Press START. The dryer starts at the beginning of the new cycle.	23
Changing Modifiers and Options after pressing Start	23
1. Press PAUSE/CANCEL once.	23
2. Select the new Option and/or Modifiers.	23
3. Press START to continue the cycle.	23
Changing the Preset Dryness Level Settings	23
1. The Dryness Level settings cannot be changed while the dryer is running.	24
2. Press and hold the DRYNESS button for 5 seconds. The dryer will beep, and “CF” will be displayed for 1 second followed by the current drying setting.	24
3. To select a new drying setting, press the DRYNESS button again until the desired drying setting is shown. NOTE: While cycling through the settings, the current setting will not flash, but the other settings will flash.	24
4. Press START to save the drying setting.	24
5. The drying setting you selected will become your new preset drying setting for all Auto Dry cycles.	24
Drying Rack Option	24
To use the drying rack	24
1. Open dryer door.	24
2. Place drying rack inside dryer drum, positioning the back wire on the ledge of the inner dryer back panel. Push down on front edge of drying rack to secure at the front of the dryer.	24
3. Put the wet items on top of the drying rack. Leave space between the items so air can reach all the surfaces.	24
4. Close the door.	24
5. Press the POWER button.	24
6. Select Timed Dry Cycle and select a temperature (see following chart). Items containing foam, rubber, or plastic must be dried on a clothesline or by using the Air Only temperature setting.	24
7. You must select a time by pressing TIME ADJUST Up or Down. Reset time as needed to complete drying. Refer to the following table.	24
8. Press (and hold) START button (about 1 second).	24
Rack Dry	24
Setting	24
Temp.	24
Time*	24
Wool Sweaters	24
Stuffed toys or pillows	24
Stuffed toys or pillows	24
Sneakers or canvas shoes	24
dryer care	25
Cleaning the Dryer Location	25
Cleaning the Lint Screen	25
IMPORTANT:	25
Every load cleaning	25
1. The lint screen is located on the top of the dryer. Pull the lint screen toward you. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.	25
2. Push the lint screen firmly back into place.	25
As needed cleaning	25
1. Roll lint off screen with your fingers.	25
2. Wet both sides of lint screen with hot water.	25
3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.	25
4. Rinse screen with hot water.	25
5. Thoroughly dry lint screen with a clean towel. Insert lint screen back into dryer.	25
Cleaning the Dryer Interior	25
1. Apply a liquid, nonflammable household cleaner to the stained area of the drum and rub with a soft cloth until stain is removed.	25
2. Wipe drum thoroughly with a damp cloth.	25
3. Tumble a load of clean cloths or towels to dry the drum.	25
Removing Accumulated Lint	25
From Inside the Dryer Cabinet	25
From the Exhaust Vent	25
Water Inlet Hoses	25
Vacation, Storage, and Moving Care	25
Non-Use or Vacation Care	25
1. Unplug dryer or disconnect power.	25
2. Clean lint screen. See “Cleaning the Lint Screen.”	25
3. Turn off the water supply to the dryer. This helps to avoid unintended flooding (due to a water pressure surge) while you are away.	25
To winterize dryer	25
1. Unplug dryer or disconnect power.	25
2. Shut off water faucet.	25
3. Disconnect water inlet hose from faucet and drain.	25
To use dryer again	25
1. Flush water pipes. Reconnect water inlet hose to faucet. Turn on water faucet.	25
2. Plug in dryer or reconnect power.	25
Moving care	26
For power supply cord-connected dryers:	26
1. Unplug the power supply cord.	26
2. Shut off water faucet.	26
3. Disconnect the water inlet hose from faucet, then drain the hose. Transport hose separately.	26
4. Make sure leveling legs are secure in dryer base.	26
5. Use masking tape to secure dryer door.	26
For direct-wired dryers:	26
1. Disconnect power.	26
2. Disconnect wiring.	26
3. Shut off water faucet.	26
4. Disconnect the water inlet hose from faucet, then drain the hose. Transport hose separately.	26
5. Make sure leveling legs are secure in dryer base.	26
6. Use masking tape to secure dryer door.	26
Reinstalling the dryer	26
Changing the Drum Light	26
To change the drum light	26
1. Unplug dryer or disconnect power.	26
2. Open the dryer door. Locate the light bulb cover on the back wall of the dryer. Remove the screw located in the lower right corner of the cover. Remove the cover.	26
3. Turn bulb counterclockwise. Replace the bulb with a 10-watt appliance bulb only. Replace the cover and secure with the screw.	26
4. Plug in dryer or reconnect power.	26
troubleshooting	26
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call... In U.S.A. www.whirlpool.com/help - In Canada www.whirlpool.ca	26
Dryer Operation	26
Dryer will not run	26
No heat	26
Unusual sounds	26
Dryer displaying code message	27
Dryer Results	27
Clothes are not drying satisfactorily, drying times are too long, or load is too hot	27
Cycle time too short	28
Lint on load	28
Stains on load or drum	28
Loads are wrinkled	28
Odors	28
Assistance or Service	29
If you need replacement parts	29
To locate FSP® replacement parts in your area:	29
In the U.S.A.	29
Our consultants provide assistance with:	29
For further assistance	29
Accessories U.S.A.	29
In Canada	29
Our consultants provide assistance with:	29
For further assistance	29
Accessories	29
Part Number	29
Accessory	29
WHIRLPOOL CORPORATION LAUNDRY WARRANTY	30
LIMITED WARRANTY	30
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Fa...	30
ITEMS EXCLUDED FROM WARRANTY	30
This limited warranty does not cover:	30
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.	30
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.	30
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.	30
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.	30
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.	30
6. Pick up and delivery. This major appliance is intended to be repaired in your home.	30
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.	30
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Whirlpool servicer is not available.	30
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Whirlpool’s published installation instructions.	30
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be easily determined.	30
DISCLAIMER OF IMPLIED WARRANTIES	30
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the du...	30
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES	30
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incide...	30
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.	30
If you think you need repair service, first see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Se...	30
SÉCURITÉ DE LA SÉCHEUSE	31
INSTRUCTIONS D’INSTALLATION	32
Outillage et pièces	32
Pièces fournies :	32
Pièces nécessaires :	32
Si l’on utilise un cordon d’alimentation électrique :	33
Exigences d’emplacement	33
Il vous faudra :	33
Dégagements de séparation à respecter	33
Dimensions de la sécheuse	33
Espacement minimum pour une installation dans un encastrement ou dans un placard	33
Exigences supplémentaires pour l'installation dans une maison mobile	34
L'installation dans une maison mobile exige :	34
Spécifications électriques - Pour le Canada seulement	34
C'est à l'utilisateur qu'incombe la responsabilité de	34
Prise murale à 4 fils 14-30R	34
Exigences concernant l'évacuation	34
En cas d'utilisation du système d'évacuation existant	35
En cas de nouveau système d'évacuation	35
Matériel pour l'évacuation	35
Conduit métallique rigide	35
Conduit métallique flexible	35
Coudes	35
Brides de serrage	35
Évacuation	35
Planification du système d’évacuation	36
Choisir un type de système d'évacuation	36
Installations d'évacuation recommandées	36
Installations standard du conduit d'évacuation à l'aide d'un conduit métallique rigide ou flexible	36
Autres installations où le dégagement est réduit	36
Dispositions spéciales pour les installations dans une maison mobile	36
Déterminer l'itinéraire d'acheminement du conduit	36
Déterminer la longueur du conduit et les coudes nécessaires pour la meilleure performance de séchage	36
Tableau des systèmes d'évacuation	37
REMARQUE : L'évacuation par l'arrière (côté gauche ou droit) fonctionne en ajoutant un coude. Pour établir la longueur maximale du conduit, ajouter un coude supplémentaire dans le tableau.	37
Nombre de change- ments de direction à 90° ou coudes	37
Type de conduit	37
Clapets de type boîte ou à persiennes	37
Clapets inclinés	37
0	37
Métallique rigide	37
1	37
Métallique rigide	37
2	37
Métallique rigide	37
3	37
Métallique rigide	37
4	37
Métallique rigide	37
Installation du système d’évacuation	37
1. Installer le clapet d'évacuation. Utiliser du composé de calfeutrage pour sceller l'ouverture murale à l'extérieur autour du clapet d'évacuation.	37
2. Raccorder le conduit d'évacuation au clapet. Le conduit doit être inséré à l'intérieur du clapet. Fixer ensemble le conduit et le clapet avec une bride de serrage de 4\	37
3. Acheminer le conduit d'évacuation jusqu'à l'emplacement de la sécheuse. Utiliser l'itinéraire le plus rectiligne possible. Voir “Déterminer l'itinéraire d'acheminement du conduit” dans “Planification du système d'évacuation”. Évit...	37
Installation des pieds de nivellement	37
1. Pour éviter d'endommager le plancher, utiliser un grand morceau de carton provenant du carton de la sécheuse. Placer le morceau de carton sous toute la longueur du bord arrière de la sécheuse.	37
2. Saisir fermement la sécheuse par la caisse (ni par le dessus ni par le panneau de commande). Déposer délicatement la sécheuse sur le carton. Voir l'illustration.	37
3. Examiner les pieds de nivellement. Trouver le symbole de repérage (losange).	37
4. Engager manuellement les pieds dans les trous prévus à cet effet. Utiliser une clé à molette pour visser les pieds jusqu'à ce que le symbole de repérage (losange) ne soit plus visible.	37
5. Placer une cornière en carton sous chacun des deux coins arrière de la sécheuse. Placer la sécheuse debout. Glisser la sécheuse sur les cornières jusqu'à ce que l'appareil soit proche de son emplacement final. Laisser assez d'espace pour co...	37
Raccordement du conduit d’évacuation	37
1. À l'aide d'une bride de serrage de 4\	37
2. Placer la sécheuse à son emplacement final. Ne pas écraser ni déformer le conduit d'évacuation.	37
3. Une fois que le conduit d'évacuation est raccordé, retirer les cornières et le carton.	37
Raccordement des tuyaux d'alimentation	37
1. Arrêter le robinet d'eau froide et retirer le tuyau d'alimentation de la laveuse.	37
2. Retirer l'ancienne rondelle de caoutchouc du tuyau d'alimentation et la remplacer par la nouvelle rondelle fournie. Si l'espace le permet, fixer l'embout femelle du connecteur en Y au robinet d'eau froide.	37
3. Fixer un tuyau court au robinet d'eau froide. Visser complètement le raccord à la main pour qu'il soit scellé au robinet.	37
4. À l'aide d'une pince, serrer les raccords en effectuant deux tiers de tour supplémentaire.	37
5. Fixer le connecteur en Y à l'embout mâle du tuyau court. Visser complètement le raccord à la main pour qu'il soit scellé au connecteur en Y.	37
6. L'un des extrémités du tuyau long comporte un treillis métallique à l'intérieur du raccord. Fixer cette extrémité au connecteur en “Y”.	37
7. Fixer le tuyau d'alimentation en eau froide de la laveuse à l'autre extrémité du connecteur en Y. Visser le raccord à la main jusqu'à ce qu'il soit fixé au connecteur en Y.	38
8. Terminer le serrage des raccords - deux tiers de tour supplémentaires avec une pince.	38
9. Fixer l'autre extrémité du long tuyau à l'électrovanne située au bas du panneau arrière de la sécheuse. Visser le raccord à la main jusqu'à ce qu'il repose sur le connecteur de l'électrovanne.	38
10. Terminer le serrage des raccords - deux tiers de tour supplémentaires avec une pince.	38
11. Vérifier que les robinets d'eau sont ouverts.	38
12. Vérifier s'il y a des fuites autour du connecteur en Y, du robinet et des tuyaux d'alimentation.	38
Réglage de l'aplomb de la sécheuse	38
Inversion du sens d'ouverture de la porte	38
1. Placer une serviette ou un linge doux sur la sécheuse ou l'espace de travail pour protéger la surface.	38
Dépose de la porte	38
1. Ouvrir la porte de la sécheuse.	38
2. Retirer la vis inférieure de chacune des deux charnières qui fixent la porte au panneau avant de la sécheuse.	38
3. Desserrer la vis supérieure de chacune des deux charnières de l'étape 2.	39
4. Retirer la porte de la sécheuse et les charnières en les soulevant à la verticale. Poser la porte sur une surface plane protégée, côté intérieur (partie interne de la porte) vers le haut. Retirer les deux vis desserrées du panneau avant d...	39
5. Retirer les quatre chevilles de plastique situées à l'extérieur de l'ouverture de la porte de la sécheuse.	39
6. Installer 4 chevilles de plastique dans les trous des vis sur la gauche de la sécheuse après avoir retiré les charnières (Étape 4).	39
Inversion de la gâche	39
1. Retirer la gâche de la porte de la sécheuse.	39
2. Retirer la vis cosmétique à l'opposé de la gâche de la porte.	39
3. Réinstaller la gâche de la porte et la vis cosmétique sur le côté opposé de leur place initiale. REMARQUE : La gâche de la porte et les chevilles d'obturation doivent être sur le même côté de l'ouverture de la porte.	39
Réinstallation de la porte	39
1. Retirer les quatre vis et les deux charnières de la porte de la sécheuse.	39
2. Replacer les quatre vis dans les mêmes trous.	39
3. Retirer les quatre vis du côté opposé de la porte.	39
4. Installer les deux charnières sur le panneau avant de la sécheuse à l'aide de quatre vis. Utiliser le côté sans fente pour fixer la charnière sur le panneau avant.	39
5. Installer les vis dans les trous supérieurs de la porte destinés à la pose des charnières. Ne pas serrer les vis. Laisser les vis en retrait d'environ ¼\	40
6. Suspendre la porte : insérer les têtes de vis dans les trous de fente supérieurs des charnières et glisser la porte vers le bas. Aligner les trous de vis inférieurs dans la charnière et la porte. Fixer deux vis inférieures. Serrer toutes le...	40
7. Fermer la porte; vérifier l'engagement de la gâche.	40
Achever l'installation	40
1. Vérifier que toutes les pièces sont maintenant installées. S'il reste une pièce, passer en revue les différentes étapes pour découvrir laquelle aurait été oubliée.	40
2. Vérifier la présence de tous les outils.	40
3. Jeter ou recycler tous les matériaux d'emballage.	40
4. Vérifier que chaque robinet d'arrivée d'eau est ouvert.	40
5. Vérifier s'il y a des fuites autour du connecteur “Y”, du robinet et des tuyaux d'alimentation.	40
6. Vérifier l'emplacement définitif de la sécheuse. S'assurer que le conduit d'évacuation n'est pas écrasé ou pincé.	40
7. Vérifier que la sécheuse est d'aplomb. Voir “Réglage de l'aplomb de la sécheuse”.	40
8. Brancher sur une prise à quatre alvéoles reliée à la terre. Mettre l'appareil sous tension.	40
9. Retirer toute pellicule de protection ou tout ruban adhésif resté(e) sur la sécheuse.	40
10. Lire “Utilisation de la sécheuse”.	40
11. Essuyer soigneusement l'intérieur du tambour de la sécheuse avec un chiffon humide pour éliminer toute trace de poussière.	40
12. Si vous habitez dans une région où l'eau est dure, il est recommandé d'utiliser un adoucisseur d'eau afin de contrôler les accumulations de calcaire dans la sécheuse. Après un certain temps, les accumulations de calcaire peuvent obstruer di...	40
13. Tester le fonctionnement de la sécheuse en sélectionnant un programme de séchage minuté avec chaleur et en mettant la sécheuse en marche. Ne pas sélectionner le modificateur Air Only (air seulement).	40
Utilisation de la sécheuse	41
Mise en marche de la sécheuse	41
1. Nettoyer le filtre à charpie avant chaque charge. Voir “Nettoyage du filtre à charpie”.	41
2. Charger les vêtements dans la sécheuse et fermer la porte.	41
3. Appuyer sur POWER (alimentation).	41
4. Tourner le bouton au programme sélectionné. Les préréglages pour les programmes automatiques ou minutés s'allument. La durée estimée (programme automatique) ou réelle (programme minuté) du programme apparaît (en minutes) sur l'afficheur.	41
5. (ÉTAPE FACULTATIVE) Si désiré, choisir OPTIONS. Pour plus de détails, voir “Options”.	42
6. (ÉTAPE FACULTATIVE) Si désiré, appuyer sur END OF CYCLE SIGNAL. Un signal sera émis pour vous annoncer la fin du programme. Pour plus de détails, voir la section “Signal de fin de programme”.	42
7. Appuyer sur START (mise en marche). Vérifier que la porte est fermée.	42
Arrêt, pause ou remise en marche	43
Pour mettre la sécheuse en pause ou l'arrêter à tout moment	43
Pour remettre la sécheuse en marche	43

Match case Limit results 1 per page

Connect ground wire (green or bare) of direct wire cable to

external ground conductor screw. Tighten screw.

A. External ground conductor screw

B. Neutral ground wire

C. Ground wire (green or bare) of power supply cord

D. ¾" (19 mm) UL listed strain relief

E. Center, silver-colored terminal block screw

F. Neutral wire (white or center wire)

Place the hooked ends of the other direct wire cable wires under

the outer terminal block screws (hooks facing right). Squeeze

hooked ends together. Tighten screws.

Tighten strain relief screw.

Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

You have completed your electrical connection. Now go to

“Venting Requirements.”

3-wire connection: Power supply cor

Use where local co

es permit connecting ca

inet-groun

con

uctor to neutral wire.

A. 3-wire receptacle (NEMA type 10-30R)

B. 3-wire plug

C. Neutral prong

D. Spade terminals with upturned ends

" (19 mm) UL listed strain relief

F. Ring terminals

G. Neutral wire (white or center wire)

Loosen or remove center, silver-colored terminal block screw.

Connect neutral wire (white or center wire) of power supply cord

to the center, silver-colored terminal screw of the terminal block.

Tighten screw.

A. External ground conductor screw

B. Neutral ground wire

C. Center, silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. ¾" (19 mm) UL listed strain relief

Connect the other wires to outer terminal block screws. Tighten

screws.

Tighten strain relief screws.

Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

You have completed your electrical connection. Now go to

“Venting Requirements.”

3-wire connection: Direct Wire

Use where local co

es permit connecting ca

inet-groun

con

uctor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can

be moved if needed.

Strip 3

" (89 mm) of outer covering from end of cable. Strip

insulation back 1" (25 mm). If using 3-wire cable with ground wire,

cut bare wire even with outer covering. Shape ends of wires into a

hook shape.

(25 mm)

½"

(89 mm)