Whirlpool WFW862CHC Owners Manual - Page 12

Preliminary, Draft

Get Whirlpool WFW862CHC PDF manuals and user guides View all Whirlpool WFW862CHC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

USING THE DISPENSERS (varies by model) 1. For automatic dispensing, open the bulk dispenser drawer using the handle at the base of the washer. For a single load, open the single load dispenser drawer at the top left corner of the washer and disable the Load & Go™ option. 2. Add laundry products as described below. 3. Slowly close the dispenser drawer. Make sure it is completely closed. NOTES: ■■ A small amount of water may remain in the single load dispenser from the previous wash cycle. This is normal. ■■ See "About Detergent Concentration" for information on detergent concentration. ■■ On some models: When detergent in the bulk dispenser is running low, the display will show the detergent level (Low). ■■ Add single-dose and Oxi-type boosters to the drum before loading items. See the "Using Your Washer" section. Adding HE detergent to dispenser Load & Go™ bulk dispenser (on some models) Use only High Efficiency (HE) liquid detergents. The bulk dispensers will hold about 67.6 oz (2 L) or 33.8 oz (1 L) of liquid HE detergent, depending on dispenser, or enough for many loads of laundry. To Fill Bulk Dispeners: Use only High Efficiency (HE) detergent. Adding detergent for a single load Selector INARY Open the dispenser drawer by pulling on the handle at PRELIM the base of the washer. If desired, the drawer can be completely removed from the washer. Tab Locate the Load & Go™ bulk DRAFT dispenser. Gently pull up on the tab located on the bulk dispenser lid to lift the fill door. Fill to the "MAX" line (see illustrations at right) with HE HE detergent compartment Use only High Efficiency (HE) detergent. Pour a measured amount of HE detergent into detergent compartment. For powdered detergent, lift the selector to the high position. For liquid detergent, push down the selector to the low position. Do not overfill; adding too much detergent may cause detergent to be dispensed into the washer too early. liquid detergent. Close fill door. It will click into place. Make sure the concentration is correct (see the "Choosing the Right Detergent" section. The dispensers should be rinsed out when changing detergents or when "MAX" line Powdered detergent: Lift the selector to the high position. Add directly to the compartment. Liquid detergent: Push down the selector to the low position. Add directly to the compartment. the washer will not be used for extended periods. For instructions on cleaning the dispenser cartridge, see the "Washer Care" section. IMPORTANT: ■■ Disable the Load & Go™ option before starting a single load. ■■ Do not add single-dose laundry packet to dispenser drawer. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
12
PRELIMINARY
DRAFT
USING THE DISPENSERS
(varies by model)
1.
For automatic dispensing, open the bulk dispenser drawer
using the handle at the base of the washer. For a single load,
open the single load dispenser drawer at the top left corner
of the washer and disable the Load & Go™ option.
2.
Add laundry products as described below.
3.
Slowly close the dispenser drawer. Make sure it is
completely closed.
NOTES:
■
A small amount of water may remain in the single load
dispenser from the previous wash cycle. This is normal.
■
See “About Detergent Concentration” for information on
detergent concentration.
■
On some models:
When detergent in the bulk dispenser is
running low, the display will show the detergent level (Low).
■
Add single-dose and Oxi-type boosters to the drum before
loading items. See the “Using Your Washer” section.
Adding HE detergent to dispenser
Powdered detergent:
Lift the selector to the high
position. Add directly to the
compartment.
Use only High Efficiency
(HE) detergent.
Load & Go
™
bulk dispenser (on some models)
Adding detergent for a single load
IMPORTANT:
■
Disable the Load & Go™ option before starting a single
load.
■
Do not add single-dose laundry packet to dispenser
drawer.
HE detergent
compartment
Use only High Efficiency (HE)
liquid detergents. The bulk
dispensers will hold about 67.6 oz
(2 L) or 33.8 oz (1 L) of liquid HE
detergent, depending on dispenser,
or enough for many loads of laundry.
To Fill Bulk Dispeners:
Open the dispenser drawer by pulling on the handle at
the base of the washer. If desired, the drawer can be
completely removed from the washer.
Locate the Load & Go™ bulk
dispenser. Gently pull up on the
tab located on the bulk dispenser
lid to lift the fill door.
Fill to the “MAX” line (see
illustrations at right) with HE
liquid detergent. Close fill door.
It will click into place. Make sure
the concentration is correct (see
the “Choosing the Right Detergent”
section.
±
The dispensers should be rinsed out
when changing detergents or when
the washer will not be used for
extended periods. For instructions
on cleaning the dispenser cartridge,
see the “Washer Care” section.
Use only High
Efficiency (HE)
detergent.
Liquid detergent:
Push down the selector
to the low position. Add
directly to the compartment.
Selector
Pour a measured amount of HE detergent into detergent
compartment. For powdered detergent, lift the selector
to the high position. For liquid detergent, push down the
selector to the low position.
Do not overfill; adding too much detergent may cause
detergent to be dispensed into the washer too early.
Tab
“MAX” line