Whirlpool WFW9150WW Owners Manual - Page 10
Level the Washer, Complete Installation - front load washer
UPC - 883049188102
View all Whirlpool WFW9150WW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
3. Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B. A B C NOTES: ■ Do not force excess drain hose back into the rear of the washer. ■ To avoid siphoning, do not seal or put more than 4½" (114 mm) of the drain hose into drainpipe or standpipe. 4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe as shown. See illustration C. Level the Washer Proper foot to floor contact and leveling your washer avoids excessive noise and vibration. NOTE: Installing washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended. 1. Slide the washer to its final location. 2. Check that all four feet are in firm contact with the floor. 3. Check the levelness of the washer by placing a level on the top edge of the washer, first side to side then front to back. Complete Installation 1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See "Electrical Requirements." 2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 3. Check that you have all of your tools. 4. Dispose of/recycle all packaging materials. 5. Check that both water faucets are on. 6. Check for leaks around faucets and inlet hoses. WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 7. Plug into a grounded 3 prong outlet. 8. Read "Washer Use." 9. To test and to clean your washer, measure ½ the detergent manufacturer's recommended amount of High Efficiency (HE) detergent for a medium-size load. Pour the detergent into the detergent dispenser. Select NORMAL and then press START/ PAUSE. Allow the washer to complete one whole cycle. If the washer is against a wall, move the washer out slightly before tipping back. If the washer is not level, first prop the front with a wooden block and adjust the front feet height moving the hexagonal plastic part as necessary. Repeat to adjust back feet. 4. Make sure all four feet are in firm contact with the floor. Then check that the washer is perfectly level (use a level). Repeat steps 1-3 until washer is level. 5. After the washer is level, and all four feet are in firm contact with the floor, use a 9/16" (14 mm) open-end wrench to turn the locknuts on the feet, tightly against the washer cabinet. IMPORTANT: All four locknuts on the feet must be tightened. If the locknuts are not tight against the washer cabinet, the washer may vibrate. 6. The washer should not move front to back, side to side, or diagonally when pushed on its top edges. 7. Confirm the levelness of the washer. Use only HE High Efficiency detergent. 10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56