Whirlpool WFW9600TA Use and Care Guide - Page 15
Status Lights - troubleshooting
UPC - 883049065908
View all Whirlpool WFW9600TA manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
To drain the washer manually 1. Press PAUSE/CANCEL twice. 2. Press POWER. 3. Select DRAIN/SPIN. 4. Press START (for approximately 1 second) to begin the drain. 5. When the spin is complete, the door unlocks. Items can be removed from the washer. Status Lights These lights show which portion of the cycle the washer is operating. They also indicate when you can add an additional item to the wash cycle and when the controls are locked. Add a garment This washer allows a 4-8 minute period in which other garments may be added to the load. You can add items to the washer if the Add a garment status light is glowing. To add items when Add a garment light is glowing 1. Select PAUSE/CANCEL once. The washer door unlocks after a few seconds, and items can be added. 2. To continue the cycle, close the door and select and hold START (for approximately 1 second). To add items when the Add a garment light is not glowing 1. You must cancel the current cycle by pressing PAUSE/ CANCEL twice. This will cancel the wash cycle and options. The washer door unlocks, and items can be added. 2. Close the door, press POWER, and select the new cycle and options. Select and hold START (for approximately 1 second). Done The Done status light stays on for 60 minutes after the cycle is complete, and then the washer shuts off. Sanitized This washer has a Sanitize water temperature that is certified by NSF International, an independent third-party testing and certification organization. The certification verifies that the sanitizing cycle reduces 99.9% of bacteria typically found on clothing, bedding, and towels, and there is no carryover of bacteria between loads after the cycle is complete. Controls Lock/Unlock The Controls Lock avoids unintended use of the washer. You can also use the control lock feature to avoid unintended cycle or option changes during a cycle. When Controls Lock is lit, all buttons are disabled except for Pause/Cancel and Start. You can lock the controls while the washer is operating. To lock the controls Press and hold CONTROLS LOCK/UNLOCK for 3 seconds after the cycle starts, or when the washer is turned off. The status light next to the CONTROLS LOCK/UNLOCK button will glow. To unlock the controls Press and hold CONTROLS LOCK/UNLOCK for 3 seconds until the status light turns off. NOTE: To lock or unlock the controls when the washer is off, press and hold CONTROLS LOCK/UNLOCK for 3 seconds. Door Locked When the status light glows, the door is locked. Sensing/Revising Estimated Time The cycle times vary automatically based on your water pressure, water temperature, detergent, and clothes load. The washer will automatically sense the progress in the cycle and adjust the Estimated Time Remaining display. While the washer is sensing, the estimated time will flash and the Sensing status light will glow. When the sensing is complete, the flashing stops, the status light goes off, and the Estimated Time Remaining display is updated. The cycle time will be extended if oversudsing occurs or the load is unbalanced. The SUD routine removes extra suds and assures proper rinsing of your garments. See "Troubleshooting." During the unbalance routine, the time displayed may pause until this activity is complete, then resume with the remainder of the cycle. Clean Washer Reminder The Clean Washer Reminder light illuminates to remind you to use the Clean Washer cycle regularly. The reminder light will illuminate every 30 cycles. The reminder light may be reset by either running the Clean Washer cycle, or by pressing the CLEAN WASHER RESET button. Certified to Sanitize If the "Sanitize" wash temperature was selected, when the wash cycle is complete, the DONE status light will illuminate, the door unlocks, and the wash load can be removed from the washer. The washer powers down automatically 60 minutes after the cycle is complete and the DONE status light turns off. 15