Whirlpool WGD7300DW Use & Care Guide - Page 16

Whirlpool WGD7300DW Manual

Get Whirlpool WGD7300DW PDF manuals and user guides View all Whirlpool WGD7300DW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Troubleshooting First try the solutions suggested here or visit our website at www.whirlpool.com/product_help In Canada www.whirlpool.ca for assistance and to possibly avoid a service call. If you experience Dryer Results (cont.) Odors (cont.) For steam cycles, the water is not properly connected with the dryer. Odors are left in garments after wearing. Make sure water is connected to the dryer. Check that water inlet hose is connected to both the faucet and dryer's water inlet valve. Check that the water supply is turned on. To remove odors left in garments after wearing, select Steam Refresh. This cycle is best for reducing wrinkles and odors from dry loads consisting of wrinkle-free cotton, cotton-polyester blends, common knits, and synthetics. Allow the dryer to complete the cooldown portion of the cycle before removing the load. Select an Automatic Cycle with a lower heat setting to avoid overdrying the load. Possible Causes Solution Load too hot Load removed before cooldown portion of cycle complete. Using Timed Dry cycle with a high temperature setting. Dryer Displaying Code Message or Indicator Is Lit "PF" (power failure) "L2" Diagnostic Code (low or no line voltage condition) The drying cycle has been interrupted Touch and hold START to restart the dryer cycle or touch power by a power failure. to clear the display. There may be a problem with your home power supply, keeping the dryer's heater from turning on. The dryer will continue to run when this diagnostic code is present. Touch any pad to clear the code from the display and return to the estimated time remaining. NOTE: This error will only show during the initial installation. Try the following: • Check to see if a household fuse has blown or circuit breaker has tripped. Electric dryers use two household fuses or breakers. Replace the fuse or reset the circuit breaker. • Confirm that the power cord is properly installed. Refer to the Installation Instructions for details. •S  elect a Timed Dry heated cycle, and restart the dryer. If the message persists, consult a qualified electrician. If a code beginning with an "F" appears in the display, alternating between F# and E#, the dryer control has detected a problem that requires service. Call for service. "F# E#" (F1 E1, F3 E1, etc.) variable service codes. The dryer is in need of service. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
16
Troubleshooting
If you experience
Possible Causes
Solution
Dryer Results (cont.)
Odors (cont.)
For steam cycles, the water is not
properly connected with the dryer.
Make sure water is connected to the dryer. Check that water
inlet hose is connected to both the faucet and dryer’s water inlet
valve. Check that the water supply is turned on.
Odors are left in garments after
wearing.
To remove odors left in garments after wearing, select Steam
Refresh. This cycle is best for reducing wrinkles and odors from
dry loads consisting of wrinkle-free cotton, cotton-polyester
blends, common knits, and synthetics.
Load too hot
Load removed before cooldown
portion of cycle complete.
Allow the dryer to complete the cooldown portion of the cycle
before removing the load.
Using Timed Dry cycle with a high
temperature setting.
Select an Automatic Cycle with a lower heat setting to avoid
overdrying the load.
Dryer Displaying Code Message or Indicator Is Lit
“PF” (power failure)
The drying cycle has been interrupted
by a power failure.
Touch and hold START to restart the dryer cycle or touch power
to clear the display.
“L2” Diagnostic Code
(low or no line voltage
condition)
There may be a problem with your
home power supply, keeping the
dryer’s heater from turning on.
The dryer will continue to run when this diagnostic code is
present. Touch any pad to clear the code from the display and
return to the estimated time remaining.
NOTE:
This error will only show during the initial installation.
Try the following:
•
Check to see if a household fuse has blown or circuit breaker
has tripped. Electric dryers use two household fuses or
breakers. Replace the fuse or reset the circuit breaker.
•
Con±rm that the power cord is properly installed. ReFer to
the Installation Instructions for details.
•
Select a Timed Dry heated cycle, and restart the dryer.
IF the message persists, consult a quali±ed electrician.
“F# E#” (F1 E1, F3 E1,
etc.) variable service
codes.
The dryer is in need of service.
If a code beginning with an “F” appears in the display, alternating
between F# and E#, the dryer control has detected a problem
that requires service. Call for service.
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -
In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.