Whirlpool WMH1162XVD Installation Instructions - Page 10

If adjustment - filters

Get Whirlpool WMH1162XVD - 1.6 cu. ft. Microwave-Range Hood Combination PDF manuals and user guides
UPC - 883049147901
View all Whirlpool WMH1162XVD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

NOTEI:fmicrowavoevendoesnotneedtobeadjustedsk, ip steps7-9. 7. If adjustmeinsrtequiredro, tatemicrowavoevendownward. Using2 ormorepeopleli,ftmicrowavoevenoffofmounting platea, ndsetasideonaprotectesdurface. 8. Loosemn ountinpglatescrewsA.djusmt ountinpglateand retightesncrews. 9. Repeastteps3-6. 10.Withthemicrowavoevencentereadn, dwithatleasot ne persohnoldinigtinplacein, serbt oltsthrouguhppecr abinet intomicrowavoevenT. ightebnoltsuntitlhereisnogap betweeunppecr abineatndmicrowavoeven. NOTES: • Someuppecrabinetms ayrequirbeoltslongeorrshortethr an 3h"a(r7d.w6camsre)t.Loorensg.eorrshortebroltsareavailabaletmost Overtightenbinogltsmaywarpthetopofthemicrowavoeven. Toavoidwarpingw,oodfillerblocks(installetorprovide) maybeaddedT.heblockms ustbethesamethicknesass tmhiecsrpoawcaebvoeevtewne.etnheuppecr abinebtottomandthe 2. Connect vent to damper assembly. A B _i iii R A. Vent B. Damper assembly (under vent) _ _ _ 7¸ __ 1. Refer to the Use and Care Guide for instructions on how to install filters into your model. [ lq A. Bolts For Roof Venting Installation Only 1. Insert damper assembly through the cabinet cutout so that the long tab of the damper assembly slides under the raised tabs of the damper plate. Then secure with sheet metal screw. NOTE: The screw cannot be installed if the damper assembly is not positioned as shown. C D E A. Raised tabs B. Damper assembly C. Sheet metal screw D. Upper cabinet cutout E. Long tab F. Damper plate Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 2. Plug microwave oven into grounded 3 prong outlet. 3. Reconnect power. 4. Check the operation of microwave oven by placing 1 cup (250 mL) of water on the turntable, and programming a cook time of 1 minute at 100% power. Test vent fan and exhaust by operating the vent fan. 5. If the microwave oven does not operate: • Check that a household fuse has not blown, or that a circuit breaker has not tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. Check that the power supply cord is plugged into a grounded 3 prong outlet. See the Use and Care Guide for troubleshooting information. Installation is now complete. Save Installation Instructions for future use. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
NOTE:
Ifmicrowave
ovendoesnotneed
tobeadjusted,
skip
steps7-9.
7. If adjustment
isrequired,
rotatemicrowave
ovendownward.
Using2ormorepeople,
liftmicrowave
ovenoffofmounting
plate,
andsetasideonaprotected
surface.
8. Loosen
mounting
platescrews.
Adjust
mounting
plateand
retighten
screws.
9. Repeat
steps3-6.
10.With
themicrowave
ovencentered,
andwithatleast
one
person
holding
itinplace,
insert
bolts
through
upper
cabinet
intomicrowave
oven.
Tighten
boltsuntil
there
isnogap
between
upper
cabinet
andmicrowave
oven.
NOTES:
•
Someupper
cabinets
mayrequire
boltslonger
orshorter
than
3"(7.6cm).Longer
orshorter
boltsareavailable
atmost
hardware
stores.
Overtightening
boltsmaywarp
thetopofthemicrowave
oven.
Toavoidwarping,
wood
fillerblocks
(installer
toprovide)
maybeadded.
Theblocks
mustbethesame
thickness
as
thespacebetween
theupper
cabinet
bottomandthe
microwave
oven.
[
lq
A. Bolts
For Roof Venting Installation Only
1.
Insert damper
assembly
through the cabinet cutout so that the
long tab of the damper
assembly
slides under the raised tabs
of the damper
plate. Then secure with sheet metal screw.
NOTE: The screw cannot
be installed if the damper
assembly
is
not positioned
as shown.
C
D
E
A. Raised
tabs
B. Damper
assembly
C. Sheet metal screw
D. Upper cabinet
cutout
E. Long
tab
F. Damper
plate
2.
Connect
vent to damper
assembly.
A
B
_i
iii
R
A. Vent
B. Damper
assembly
(under vent)
_
_
_
7¸
_
_
1.
Refer to the Use and Care Guide for instructions
on how to
install filters into your model.
Electrical
Shock
Hazard
Plug into
a
grounded
3 prong
outlet.
Do
not
remove
ground prong.
Do not
use an adapter.
Do not
use an extension
cord.
Failure
to follow
these
instructions
can result
in
death,
fire, or electrical
shock.
2.
Plug microwave
oven into grounded
3 prong outlet.
3.
Reconnect
power.
4.
Check the operation
of microwave
oven by placing 1 cup
(250 mL) of water on the turntable,
and programming
a cook
time of 1 minute at 100% power. Test vent fan and exhaust
by
operating
the vent fan.
5.
If the microwave
oven does not operate:
•
Check that a household
fuse has not blown, or that a
circuit
breaker has not tripped.
Replace the fuse or reset
the circuit
breaker. If the problem
continues,
call an
electrician.
Check that the power supply
cord is plugged
into a
grounded
3 prong outlet.
See the Use and Care Guide for troubleshooting
information.
Installation
is now complete.
Save Installation
Instructions
for future use.
10