Whirlpool WTW5100VQ Installation Instructions - Page 3

Location Requirements, Drain System - top load

Get Whirlpool WTW5100VQ - 3.2 cu. Ft. Washer PDF manuals and user guides
UPC - 883049145143
View all Whirlpool WTW5100VQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Location Requirements Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk". Your washer can be installed in a basement, laundry room, closet, or recessed area. See "Drain System." IMPORTANT: Do not install or store the washer where it will be exposed to the weather. Proper installation is your responsibility. You will need: I A water heater set to deliver 120°F (49°C) water to the washer. I A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements." I Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water ll valves, and water pressure of 5-100 psi (34.5-690 kPa). Washers with triple dispensers require 20-100 psi (138-690 kPa) for best performance. I A level oor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended. I A sturdy oor to support the washer weight (washer, water, and load) of 315 lbs (143 kgs). Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer Care" in the Washer User Instructions for winterizing information. Recessed area or closet installation The dimensions shown are for the recommended spacing allowed (A and B), except the closet door ventilation openings. The dimensions shown for the closet door ventilation openings (C) are the minimum required. 19" (48.3 cm) 14" max. (35.6 cm) 48 in.2 (310 cm2) 3" (7.6 cm) 24 in.2 (155 cm2) 0" 27" 0" 1" 251⁄2" (0 cm) (68.6 cm) (0 cm) (2.5 cm) (64.8 cm) 4" (10.2 cm) A B A. Front view B. Side view C. Closet door with vents 3" (7.6 cm) C I Additional spacing should be considered for ease of installation and servicing. I Additional clearances may be required for wall, door, and oor moldings. I Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce noise transfer. I If a closet door is installed, the minimum air openings in the top and bottom of the door are required (C). Louvered doors with air openings in the top and bottom are acceptable. I Companion appliance spacing should also be considered. Drain System The washer can be installed using the standpipe drain system ( oor or wall), the laundry tub drain system, or the oor drain system. Select the drain hose installation method you need. See "Tools and Parts." Standpipe drain system-wall or oor (views A & B) The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 11⁄4" (3.2 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See "Tools and Parts." The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm) from the bottom of the washer. IMPORTANT: To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be inside the standpipe. See "Connect drain hose." 39" (99 cm) A B Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 39" (99 cm) above the oor and no higher than 96" (244 cm) from the bottom of the washer. Floor drain system (view D) The oor drain system requires a siphon break that may be purchased separately. See "Tools and Parts." The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed. To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be below the top of the wash tub. Secure drain hose with beaded tie strap. 39" (99 cm) 28" (71 cm) C D 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk”.
Your washer can be installed in a basement, laundry room, closet,
or recessed area. See “Drain System.”
IMPORTANT:
Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
±
A water heater set to deliver 120°F (49°C) water to the washer.
±
A grounded electrical outlet located within 4 ft (1.2 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
±
Hot and cold water faucets located within 3 ft (90 cm) of the
hot and cold water ±ll valves, and water pressure of 5-100 psi
(34.5-690 kPa). Washers with triple dispensers require
20-100 psi (138-690 kPa) for best performance.
±
A level ²oor with a maximum slope of 1" (2.5 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
±
A sturdy ²oor to support the washer weight (washer, water,
and load) of 315 lbs (143 kgs).
Do not store or operate your washer in temperatures at or below
32°F (0°C). Some water can remain in the washer and can cause
damage in low temperatures. See “Washer Care” in the Washer
User Instructions for winterizing information.
Recessed area or closet installation
The dimensions shown are for the recommended spacing allowed
(A and B), except the closet door ventilation openings. The
dimensions shown for the closet door ventilation openings (C)
are the minimum required.
±
Additional spacing should be considered for ease
of installation and servicing.
±
Additional clearances may be required for wall, door,
and ²oor moldings.
±
Additional spacing of 1" (2.5 cm) on all sides of the washer
is recommended to reduce noise transfer.
±
If a closet door is installed, the minimum air openings in the
top and bottom of the door are required (C). Louvered doors
with air openings in the top and bottom are acceptable.
±
Companion appliance spacing should also be considered.
Drain System
The washer can be installed using the standpipe drain system
(²oor or wall), the laundry tub drain system, or the ²oor drain
system. Select the drain hose installation method you need.
See “Tools and Parts.”
Standpipe drain system—wall or ±oor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 1
1
/
4
" (3.2 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter kit is available. See “Tools and Parts.”
The top of the standpipe must be at least 39" (99 cm) high
and no higher than 96" (244 cm) from the bottom of the washer.
IMPORTANT:
To avoid siphoning, no more than 8" (20.3 cm) of
drain hose should be inside the standpipe. See “Connect drain hose.”
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 39" (99 cm) above the ²oor and
no higher than 96" (244 cm) from the bottom of the washer.
Floor drain system (view D)
The ²oor drain system requires a siphon break that may be
purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 28" (71 cm) from the
bottom of the washer. Additional hoses might be needed.
To avoid siphoning, no more than 8" (20.3 cm) of drain hose
should be below the top of the wash tub. Secure drain hose
with beaded tie strap.
19"
(48.3 cm)
0"
(0 cm)
0"
(0 cm)
4"
(10.2 cm)
1"
(2.5 cm)
27"
(68.6 cm)
25
1
/
2
"
(64.8 cm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
3"
(7.6 cm)
3"
(7.6 cm)
14" max.
(35.6 cm)
A. Front view
B. Side view
C. Closet door with vents
A
B
C
A
B
39"
(99 cm)
39"
(99 cm)
28"
(71 cm)
C
D
3