Yamaha 5990 MCXSP10 Manual - Page 116

Problem, Cause, Remedy, The remote control, does not work or, function properly., does not learn new

Get Yamaha 5990 - HTR AV Receiver PDF manuals and user guides View all Yamaha 5990 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

TROUBLESHOOTING ■ Remote control Problem The remote control does not work or function properly. The remote control does not learn new functions. Cause Remedy Wrong distance or angle. The remote control will function within a maximum range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel. Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition this unit. The batteries are weak. Replace all batteries. AMP/SOURCE/TV is set incorrectly. Set AMP/SOURCE/TV correctly. When operating this unit, set it to the AMP position. When operating the component selected by the input selector button, set it to the SOURCE position. When operating the TV set in the DTV or PHONO area, set it to the TV position. The remote control code was not correctly set. Set the remote control code correctly using "LIST OF REMOTE CONTROL CODES" at the end of this manual. Try setting another code of the same manufacturer using "LIST OF REMOTE CONTROL CODES" at the end of this manual. The library code of the remote control and the remote control ID of this unit do not match. Match the remote control ID of this unit with the corresponding remote control library code. Even if the remote control code is correctly set, there are some models that do not respond to the remote control. Program the necessary functions independently into the programmable buttons using the Learn feature. The batteries of this remote control and/or Replace the batteries. the other remote control are too weak. The distance between the two remote controls is too much or too little. Place the remote controls at the proper distance. The signal coding or modulation of the other remote control is not compatible with this remote control. Learning is not possible. Memory capacity is full. Delete other unnecessary functions to make room for the new functions. See page 4 - 4 - 92 92 89, 92 94 4 94 - 99 112

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
112
TROUBLESHOOTING
■
Remote control
Problem
Cause
Remedy
See
page
The remote control
does not work or
function properly.
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
4
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
4
AMP/SOURCE/TV is set incorrectly.
Set AMP/SOURCE/TV correctly.
When operating this unit, set it to the AMP position.
When operating the component selected by the input
selector button, set it to the SOURCE position.
When operating the TV set in the DTV or PHONO
area, set it to the TV position.
—
The remote control code was not correctly
set.
Set the remote control code correctly using
“LIST OF REMOTE CONTROL CODES” at the end
of this manual.
92
Try setting another code of the same manufacturer
using “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
92
The library code of the remote control and
the remote control ID of this unit do not
match.
Match the remote control ID of this unit with the
corresponding remote control library code.
89, 92
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Program the necessary functions independently into
the programmable buttons using the Learn feature.
94
The remote control
does not learn new
functions.
The batteries of this remote control and/or
the other remote control are too weak.
Replace the batteries.
4
The distance between the two remote
controls is too much or too little.
Place the remote controls at the proper distance.
94
The signal coding or modulation of the
other remote control is not compatible
with this remote control.
Learning is not possible.
—
Memory capacity is full.
Delete other unnecessary functions to make room for
the new functions.
99