Yamaha AVX-S80 Owner's Manual - Page 47

Appendix, Troubleshooting, General

Page 47 highlights

TROUBLESHOOTING Refer to the chart below when this system does not function properly. If the problem you are having is not listed below or if the instruction below does not help, set this system to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. I General Problem This system fails to turn on when STANDBY/ON (or POWER ( ) is pressed, or enters in the standby mode soon after the power has been turned on. No sound. The sound suddenly goes off. Only the speaker on one side can be heard. Sound can be heard only from the front speakers. Cause The power cord is not connected or the plug is not completely inserted. This system has been exposed to a strong external electric shock (such as lightning and strong static electricity). Incorrect input or output cable connections. An appropriate input source has not been selected. The speaker connections are not secure. The volume is turned down. The sound is muted. The source that this system cannot reproduce, such as a CD-ROM, is being played. The sleep timer has functioned. Incorrect cable connections. The sound effect is off. A Dolby Surround, Dolby Digital or DTS decoding DSP program is being used with material not encoded with Dolby Surround, Dolby Digital or DTS. A 96-kHz sampling digital signal is being input to this system. Remedy Firmly connect the power cord. Refer to page - Set this system in the standby mode, disconnect - the power cord, plug it back in after 30 seconds, then start operating. Connect the cables properly. If the problem persists, the cables may be defective. Select an appropriate input source with the input selector buttons. Secure the connections. Turn up the volume. Press MUTE or any operation buttons of this system to cancel a mute and adjust the volume. Play a source whose signals this system can reproduce. Turn on the power, and play the source again. 12 - 17 19 15 - 16 19 19 - 20 Connect the cables properly. If the problem persists, the cables may be defective. 15 - 16 Press STEREO to turn it on. Select another DSP program. 25 21 - 22 When a 96-kHz sampling digital signal is being 25 input to this system, sound is output from the front speakers only. APPENDIX English 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55

43
APPENDIX
English
TROUBLESHOOTING
Refer to the chart below when this system does not function properly. If the problem you are having is not listed below
or if the instruction below does not help, set this system to the standby mode, disconnect the power cord, and contact the
nearest authorized YAMAHA dealer or service center.
General
Problem
This system fails to
turn on when
STANDBY/ON (or
POWER (
) is
pressed, or enters in
the standby mode
soon after the power
has been turned on.
No sound.
The sound suddenly
goes off.
Only the speaker on
one side can be
heard.
Sound can be heard
only from the front
speakers.
Cause
The power cord is not connected or the plug
is not completely inserted.
This system has been exposed to a strong
external electric shock (such as lightning and
strong static electricity).
Incorrect input or output cable connections.
An appropriate input source has not been
selected.
The speaker connections are not secure.
The volume is turned down.
The sound is muted.
The source that this system cannot reproduce,
such as a CD-ROM, is being played.
The sleep timer has functioned.
Incorrect cable connections.
The sound effect is off.
A Dolby Surround, Dolby Digital or DTS
decoding DSP program is being used with
material not encoded with Dolby Surround,
Dolby Digital or DTS.
A 96-kHz sampling digital signal is being
input to this system.
Remedy
Firmly connect the power cord.
Set this system in the standby mode, disconnect
the power cord, plug it back in after 30 seconds,
then start operating.
Connect the cables properly. If the problem
persists, the cables may be defective.
Select an appropriate input source with the
input selector buttons.
Secure the connections.
Turn up the volume.
Press MUTE or any operation buttons of this
system to cancel a mute and adjust the volume.
Play a source whose signals this system can
reproduce.
Turn on the power, and play the source again.
Connect the cables properly. If the problem
persists, the cables may be defective.
Press STEREO to turn it on.
Select another DSP program.
When a 96-kHz sampling digital signal is being
input to this system, sound is output from the
front speakers only.
Refer
to page
12
17
19
15
16
19
19
20
15
16
25
21
22
25