Yamaha CD-S2100 Owners Manual - Page 30

On USB connection, Problem, Cause, Remedy

Get Yamaha CD-S2100 PDF manuals and user guides View all Yamaha CD-S2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

SPECIFICATIONS Troubleshooting Problem Cause Remedy Noise from a nearby tuner. Noise from inside of the disc tray. No sound from the component connected to the DIGITAL IN (OPTICAL or COAXIAL) jack. The remote control does not work. The tuner is too close to this unit. Move the tuner and this unit farther apart. The disc may be warped. Replace the disc. The output audio source setting on the connected component is not "PCM." Only PCM audio sources can be played via the DIGITAL IN (OPTICAL/COAXIAL) jacks of this unit. Set the output audio source of the connected component to "PCM." The batteries of the remote control are too weak. Replace the batteries with new ones. Remote control is too far away or tilted too much. Use within 6 m and 60° radius. Direct sunlight or lighting (of an inverter type fluorescent lamp etc.) is striking the remote control sensor of this unit. Reposition this unit. See page - 28 - 16 16 8 ■ On USB connection Problem Cause Remedy The connected PC does not recognize this unit. Noisy playback. Music files cannot be played. The operating system of the PC is not supported. Use a PC with an operation-guaranteed operating system. Improper USB cable connection Connect the USB cable properly. The output of the PC or application is muted. Cancel the sound muting of the PC or application. Another application is launched on the PC while a music file is being played. If another application is launched while a music file is being played, sound may be momentarily lost or noise may be generated. Do not launch other applications during playback. The music data are not properly reproduced, because this unit is connected to the PC or the input of this unit is switched to "USB" while the music application is running on the PC. Connect this unit to the PC and set the input of the unit to "USB" in advance. Then launch the music application and start playback. The dedicated "Yamaha Steinberg USB Driver" Install the "Yamaha Steinberg USB Driver" has not been installed correctly. again, following the correct procedure. See page 22 19, 22 - - 22, 23 22 30 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
30
En
Troubleshooting
■
On USB connection
Problem
Cause
Remedy
See
page
Noise from a nearby
tuner.
The tuner is too close to this unit.
Move the tuner and this unit farther apart.
—
Noise from inside of
the disc tray.
The disc may be warped.
Replace the disc.
28
No sound from the
component
connected to the
DIGITAL IN (OPTICAL
or COAXIAL) jack.
The output audio source setting on the connected
component is not “PCM.”
Only PCM audio sources can be played via the
DIGITAL IN (OPTICAL/COAXIAL) jacks of
this unit.
Set the output audio source of the connected
component to “PCM.”
—
The remote control
does not work.
The batteries of the remote control are too weak.
Replace the batteries with new ones.
16
Remote control is too far away or tilted too
much.
Use within 6 m and 60° radius.
16
Direct sunlight or lighting (of an inverter type
fluorescent lamp etc.) is striking the remote
control sensor of this unit.
Reposition this unit.
8
Problem
Cause
Remedy
See
page
The connected PC
does not recognize
this unit.
The operating system of the PC is not supported.
Use a PC with an operation-guaranteed operating
system.
22
Improper USB cable connection
Connect the USB cable properly.
19, 22
The output of the PC or application is muted.
Cancel the sound muting of the PC or
application.
—
Noisy playback.
Another application is launched on the PC while
a music file is being played.
If another application is launched while a music
file is being played, sound may be momentarily
lost or noise may be generated.
Do not launch other applications during
playback.
—
Music files cannot be
played.
The music data are not properly reproduced,
because this unit is connected to the PC or the
input of this unit is switched to “USB” while the
music application is running on the PC.
Connect this unit to the PC and set the input of
the unit to “USB” in advance. Then launch the
music application and start playback.
22, 23
The dedicated “Yamaha Steinberg USB Driver”
has not been installed correctly.
Install the “Yamaha Steinberg USB Driver”
again, following the correct procedure.
22