Yamaha CDC-906 Owner's Manual - Page 8

Connections

Get Yamaha CDC-906 PDF manuals and user guides View all Yamaha CDC-906 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

PREPARATIONS Connections Never plug in this unit and other components until all connections are completed. • Before making any connections, switch OFF the power to the unit and the amplifier or other components. • Connections should be made to the correct input terminals of the amplifier or other components. • If the placement of this unit causes noise in other equipment, such as a tuner, separate them from each other. LINE OUT R L 1 LINE OUT R L 1 OPTICAL DIGITAL AUDIO OUT 1 Pin cable (included) OPTICAL DIGITAL AUDIO OUT 2 Optical fiber cable (not included) To AC outlet L R CD ANALOG IN OPTICAL DIGITAL IN Amplifier Choose one of the ways listed below to connect this unit to your amplifier. When the LINE OUT (analog) terminals of this unit are used (1) • Be sure that the left (L) and right (R) LINE OUT terminals are connected to the corresponding (left and right) terminals of the amplifier or other components. • Connect the LINE OUT terminals to the "CD" (or "AUX") terminals of the amplifier. For additional details concerning these connections, refer to the operation instructions for the amplifier being used. • The LINE OUT terminals of this unit are numbered !. When connecting this unit with a YAMAHA amplifier or receiver whose terminals on the rear panel are numbered as !, @, #, etc., connect the LINE OUT terminals of this unit to the input terminals numbered ! on the rear of the amplifier or receiver. When the DIGITAL AUDIO OUT (OPTICAL) terminal of this unit is used (2) • Before using this terminal, remove the terminal's cover by pulling it. • Make the connection from this terminal to the optical input terminal of an amplifier by using a commercially available optical fiber cable. * Be sure to use a high quality optical fiber cable. Other cables might not function correctly. • Be sure to attach the terminal cover when this terminal is not being used in order to protect the terminal from dust. • CDC-906 only Set the level of signals output into an amplifier to max. by using the OUTPUT LEVEL -/+ buttons. E-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
E-
4
PREPARATIONS
Connections
Never plug in this unit and other components until all connections are completed.
•
Before making any connections, switch OFF the power to the unit and the amplifier or other components.
•
Connections should be made to the correct input terminals of the amplifier or other components.
•
If the placement of this unit causes noise in other equipment, such as a tuner, separate them from each other.
Choose one of the ways listed below to connect this unit to your amplifier.
When the LINE OUT (analog) terminals of this unit are used (
1
)
•
Be sure that the left (
L
) and right (
R
)
LINE OUT
terminals are connected to the corresponding (left and right) terminals of
the amplifier or other components.
•
Connect the
LINE OUT
terminals to the “CD” (or “AUX”) terminals of the amplifier. For additional details concerning
these connections, refer to the operation instructions for the amplifier being used.
•
The
LINE OUT
terminals of this unit are numbered
!
. When connecting this unit with a YAMAHA amplifier or receiver
whose terminals on the rear panel are numbered as
!
,
@
,
#
, etc., connect the
LINE OUT
terminals of this unit to the
input terminals numbered
!
on the rear of the amplifier or receiver.
When the DIGITAL AUDIO OUT (OPTICAL) terminal of this unit is used (
2
)
•
Before using this terminal, remove the terminal’s cover by pulling it.
•
Make the connection from this terminal to the optical input terminal of an amplifier by using a commercially available
optical fiber cable.
*
Be sure to use a high quality optical fiber cable. Other cables might not function correctly.
•
Be sure to attach the terminal cover when this terminal is not being used in order to protect the terminal from dust.
•
CDC-906 only
Set the level of signals output into an amplifier to max. by using the
OUTPUT LEVEL –/+
buttons.
1
DIGITAL IN
ANALOG IN
CD
OPTICAL
R
L
R
L
1
LINE OUT
DIGITAL AUDIO OUT
OPTICAL
To AC outlet
2
Optical fiber cable
(not included)
1
Pin cable
(included)
Amplifier