Yamaha CS-R5 CS-R5 Owners Manual [English] - Page 23

Power Supply, Shutdown

Get Yamaha CS-R5 PDF manuals and user guides View all Yamaha CS-R5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Power Supply / Shutdown Connecting to power sources 1. Turn off both power switches A and B on the unit. 2. Connect one of the supplied power cords to AC IN connector (A), and the other to AC IN connector (B). 3. Connect the other end of each power cord to an AC outlet of a different power source. NOTE • Follow this procedure in reverse order when disconnecting the power cords. • To disconnect each power cord, remove it while pressing the latch on the plug. Shutting down the power to the unit Before you turn off the power to the control surface, Yamaha recommends that you store the current status to scene memory. If you change the connection status of the components after the power is turned off, some settings, such as patching, may be altered when you turn the power on again. For more information on storing a scene, please refer to the RIVAGE PM series Operation Manual. NOTICE If you turn off the power to the control surface without following the shutdown procedure, data inside the built-in storage may be damaged. Be sure to perform the shutdown procedure to turn off the power to the control surface. 1. Press the [SYSTEM] key (see  on page 13) for two seconds or longer. A message will ask you to confirm the shutdown operation. Warning Use only the supplied AC power cords. Using other cords may lead to overheating or electric shock. Caution Be sure to turn off the power to the unit before connecting or disconnecting the power cords. 2. To turn the power off, press the OK button. To cancel shutdown, press the CANCEL button. 3. Wait until the LEDs on the panel turn off and the touch screens go dark. 4. Turn off both power switches A and B on the rear panel. NOTICE • If you plan to turn on the power to the control surface again, wait at least five seconds before switching the power on. Otherwise, the unit may malfunction. • Even when the power switches are turned off, a small amount of current still flows through the unit. If you plan not to use the unit for a long period of time, remove the power cords from the AC outlets. CS-R5 Owner's Manual 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
CS-R5 Owner’s Manual
23
Connecting to power sources
1.
Turn off both power switches A and B on the
unit.
2.
Connect one of the supplied power cords to
AC IN connector (A), and the other to AC IN
connector (B).
3.
Connect the other end of each power cord to
an AC outlet of a different power source.
NOTE
•
Follow this procedure in reverse order when disconnecting the
power cords.
•
To disconnect each power cord, remove it while pressing the
latch on the plug.
Warning
Use only the supplied AC power cords. Using other cords may
lead to overheating or electric shock.
Caution
Be sure to turn off the power to the unit before connecting or
disconnecting the power cords.
Shutting down the power to
the unit
Before you turn off the power to the control surface,
Yamaha recommends that you store the current status to
scene memory.
If you change the connection status of the components
after the power is turned off, some settings, such as
patching, may be altered when you turn the power on
again. For more information on storing a scene, please
refer to the RIVAGE PM series Operation Manual.
NOTICE
If you turn off the power to the control surface without following
the shutdown procedure, data inside the built-in storage may be
damaged. Be sure to perform the shutdown procedure to turn off
the power to the control surface.
1.
Press the [SYSTEM] key (see
4
on page 13)
for two seconds or longer.
A message will ask you to confirm the shutdown
operation.
2.
To turn the power off, press the OK button. To
cancel shutdown, press the CANCEL button.
3.
Wait until the LEDs on the panel turn off and
the touch screens go dark.
4.
Turn off both power switches A and B on the
rear panel.
NOTICE
•
If you plan to turn on the power to the control surface again,
wait at least five seconds before switching the power on.
Otherwise, the unit may malfunction.
•
Even when the power switches are turned off, a small amount
of current still flows through the unit. If you plan not to use the
unit for a long period of time, remove the power cords from the
AC outlets.
Power Supply /
Shutdown