Yamaha CVP-405 Owner's Manual - Page 204
Guide, Score, The Guide lamps do not indicate how to play chords.
View all Yamaha CVP-405 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 204 highlights
Song playback stops before the Song is finished. • The Guide function is turned on. (In this case, playback is "waiting" for the correct key to be played.) Press the [GUIDE] button to turn off the guide function. The Song last selected before turning off the power is no longer available. • If the Song last selected before turning off the power is contained in USB storage device, you'll need to reinsert/ reconnect the same USB storage device to call up the Song again. The measure number is different from that of the score in the Song Position display, shown by pressing the [REW]/[FF] buttons. • This happens when playing back music data for which a specific, fixed tempo is set. In the AB Repeat function, the B point cannot be set. • The A point has not been set. Set the B point only after setting the A point. When playing back a Song, some channels do not play. • Playback of these channels may be set to "OFF." Turn playback on for those channels that are set to "OFF" (page 139). A Song to which write-protect has been applied ("Prot. 2 Edit" is shown at the upper left of the Song name) cannot be moved to external media such as a SmartMedia card or floppy disk. • A Song to which write-protect has been applied cannot be moved to an external media such as SmartMedia/ floppy disk, etc. Use the [USB TO DEVICE] terminal to move the song to a USB flash memory device connected to this instrument. The Tuning Curve of the piano Voice does not quite match that of other instruments' Voices. • The Tuning Curve designed especially for piano Voices may not sound with the appropriate pitches when used with other instrument Voices. Set the Tuning Curve to "FLAT" (page 97). Guide The melody still plays back, even when specifying Track 1 as the part to be muted for one-handed practice. • A part other than the melody part has been assigned to Track 1. Reassign the channel containing the melody to Track 1 (page 138). The Guide lamps do not light during Song playback, even after pressing the [GUIDE] button. • Make sure to turn on the Guide lamps (page 137). • Any notes outside of the 88-key range cannot be indi- cated by the Guide lamps. The Guide lamps light an octave or two lower/higher than the actual pitch. • The Guide lamps sometimes light an octave or two lower/higher than the actual pitch depending on the selected Voice. The lamps in the chord section of the keyboard light. • The Guide function for chords (page 50) has been enabled. Turn the Style off by pressing the [ACMP ON/ OFF] button. The Guide lamps do not indicate how to play chords. • Make sure that the Guide Mode is set to "FollowLights" (page 104). • You cannot check how to play chords with the Guide lamps if the chord fingering method is set to "Single Finger," "Full Keyboard" or "AI Full Keyboard." Select another fingering method (page 104). Score When displaying the music score, long notes that have been entered, such as whole notes and ties, are not displayed correctly. • Long notes, such as whole notes and ties, may not be shown in the music score display exactly as they were entered. Selecting "Tenuto" by pressing the [H] button before inputting each note in the Step Record display (page 145) may solve the problem. The tempo, beat, measure and music notation is not displayed correctly. • Some Song data for the instrument has been recorded with special "free tempo" settings. For such Song data, the tempo, beat, measure and music notation will not be displayed correctly. The note name partially obscures the note in the display. • When several notes occur close to each other, the note name may obscure the note at left. The music score of the right-hand/left-hand part is not displayed. • The appropriate channels have not been assigned to the right-hand and left-hand parts. Set RIGHT and LEFT to the appropriate channels (page 39). The notation in the display is cut off, with the middle of a measure starting on the next line. • When all the notes of a measure cannot fit on one line, the remaining notes in the measure are carried over to the next line. Dotted notes are indicated as rests. • This is normal; sometimes dotted notes are indicated as rests. Chords are not displayed. • If the selected Song does not contain chord data, chords are not displayed. Appendix 204 CVP-405/403/401 Owner's Manual