Yamaha DSP-A2070 Owner's Manual - Page 13

Audio Signal Connection Jacks for Audio Source Equipment - integrated amplifier

Get Yamaha DSP-A2070 PDF manuals and user guides View all Yamaha DSP-A2070 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

1 GND Terminal Connects the ground wire of the turntable to produce minimum hum. In some cases, however, better results may be obtained with the ground wire disconnected. 2 Audio Signal Connection Jacks (for Audio Source Equipment) Connect the inputs and/or outputs of your audio equipment. 3 Audio/Video Signal Connection Jacks (for Video Source Equipment) Connect the audio and video inputs and/or outputs of your video equipment. In place of the VIDEO jacks, the S VIDEO jacks can be used for higher resolution and improved picture quality if your VCR, monitor, etc. are equipped with S-VIDEO connectors. 4 Main Speaker Terminals When using this unit's built-in main-channel amplifier, connect the main speakers here. The jumper bars must be plugged in to connect the MAIN IN jacks to the MAIN OUT jacks. 5 Front Effect Speaker Terminals When using the built-in front-channel amplifier, connect the front effect speakers here. 6 Center Speaker Terminals When using the built-in center-channel amplifier, connect one or two center speakers here. 7 Center Speaker Impedance Switch Set to "A + B" when using two center speakers, or to "A or B" when using only one center speaker. 8 Rear Effect Speaker Terminals When using the built-in rear-channel amplifier, connect the rear effect speakers here. 9 Video NTSC/PAL Switch (General Model only) Set this switch to the position corresponding to the standard that your video equipment employs. 0 Front Mix Switch Set to "OFF" when setting up a full 7 or 6 speaker system, or to "ON" when setting up a 5 or 4 speaker system. A Main Level Control Adjusts the main-channel line output level at the MAIN OUT jacks. Used to achieve balance between the main and effect speakers. B Main Out Jacks Main-channel line output. Connected with jumper bars to MAIN IN jacks when the built-in amplifier is used. Connected to input jacks of external stereo power amplifier (MAIN IN or TAPE PLAY jacks of integrated amplifier or receiver) when using external amplification. C Main In Jacks Line input to built-in main-channel amplifier. Connected with jumper bars to MAIN OUT jacks when the built-in amplifier is used. Not connected when using an external power amplifier. D Center Out Jacks Center-channel line outputs. Not connected when the built-in amplifier is used. Can be connected to input jack(s) of one or two external power amplifier(s) to drive the center speaker(s). 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
1
GND Terminal
Connects the ground wire of the turntable to produce minimum
hum. In some cases, however, better results may be obtained
with the ground wire disconnected.
2
Audio Signal Connection Jacks (for Audio Source Equipment)
Connect the inputs and/or outputs of your audio equipment.
3
Audio/Video Signal Connection Jacks (for Video Source
Equipment)
Connect the audio and video inputs and/or outputs of your video
equipment. In place of the VIDEO jacks, the S VIDEO jacks can
be used for higher resolution and improved picture quality if your
VCR, monitor, etc. are equipped with S-VIDEO connectors.
4
Main Speaker Terminals
When using this unit’s built-in main-channel amplifier, connect the
main speakers here. The jumper bars must be plugged in to
connect the MAIN IN jacks to the MAIN OUT jacks.
5
Front Effect Speaker Terminals
When using the built-in front-channel amplifier, connect the front
effect speakers here.
6
Center Speaker Terminals
When using the built-in center-channel amplifier, connect one or
two center speakers here.
7
Center Speaker Impedance Switch
Set to “A + B” when using two center speakers, or to “A or B”
when using only one center speaker.
8
Rear Effect Speaker Terminals
When using the built-in rear-channel amplifier, connect the rear
effect speakers here.
9
Video NTSC/PAL Switch (General Model only)
Set this switch to the position corresponding to the standard
that your video equipment employs.
0
Front Mix Switch
Set to “OFF” when setting up a full 7 or 6 speaker system, or to
“ON” when setting up a 5 or 4 speaker system.
A
Main Level Control
Adjusts the main-channel line output level at the MAIN OUT
jacks. Used to achieve balance between the main and effect
speakers.
B
Main Out Jacks
Main-channel line output. Connected with jumper bars to MAIN
IN jacks when the built-in amplifier is used. Connected to input
jacks of external stereo power amplifier (MAIN IN or TAPE PLAY
jacks of integrated amplifier or receiver) when using external
amplification.
C
Main In Jacks
Line input to built-in main-channel amplifier. Connected with
jumper bars to MAIN OUT jacks when the built-in amplifier is
used. Not connected when using an external power amplifier.
D
Center Out Jacks
Center-channel line outputs. Not connected when the built-in
amplifier is used. Can be connected to input jack(s) of one or two
external power amplifier(s) to drive the center speaker(s).
11