Yamaha DSP-A2070 Owner's Manual - Page 25

Adjustment, Main/center/effect Speaker Level Balance, Adjustment - dsp amplifier

Get Yamaha DSP-A2070 PDF manuals and user guides View all Yamaha DSP-A2070 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

1-4. ADJUSTMENT MAIN/CENTER/EFFECT SPEAKER LEVEL BALANCE ADJUSTMENT This operation uses an internal test-tone generator for balancing the levels of the main, center and effect speakers. 1. Depress the TEST switch on the remote control so that "TEST DOLBY" appears in the display panel to enter test mode. A hiss-like calibration signal should be heard from the left main speaker, center speaker(s), right main speaker and rear effect speakers in turn (see diagram). Adjust the MASTER VOLUME to a normal listening level. Left main LEFT Center CENTER Rear SURROUND Right main RIGHT 2. Adjust the center and rear level by using the CENTER and REAR LEVEL +/- keys on the remote control so that the sound coming from the corresponding speakers seems to be at the same level as that from the main speakers when you are at a normal listening position. If there is insufficient volume from the effect speakers, you may decrease the main speaker volume level by using the MAIN LEVEL control on the rear panel and adjust the center and rear level again. Volume controls on external power amplifiers may also be adjusted if necessary to achieve proper balance. 3. For the front effect speaker level adjustment, depress the TEST switch on the remote control again so that "TEST DSP" appears in the display panel. A calibration signal should be heard from the main speakers and the front effect speakers in turn (see diagram). Main Front MAIN FRONT 4. Adjust the front level by using the FRONT LEVEL +/- keys on the remote control so that the speaker volume is the same as that of the main speakers. NOTE: If not using a center speaker, be sure to set the CENTER MODE to the PHNTM (phantom) position. You will then hear the center channel test tone from the left and right main speakers. After completing this adjustment, press the TEST switch once again. NOTE: Once you have completed these adjustments, use only this unit's MASTER VOLUME control to adjust listening volume. Do not change any other volume settings in the system. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
1-4. ADJUSTMENT
MAIN/CENTER/EFFECT SPEAKER LEVEL BALANCE
ADJUSTMENT
This operation uses an internal test-tone generator for balancing
the levels of the main, center and effect speakers.
1.
Depress the TEST switch on the remote control so that “TEST
DOLBY” appears in the display panel to enter test mode. A hiss-like
calibration signal should be heard from the left main speaker, center
speaker(s), right main speaker and rear effect speakers in turn (see
diagram). Adjust the MASTER VOLUME to a normal listening level.
2.
Adjust the center and rear level by using the CENTER and REAR
LEVEL +/– keys on the remote control so that the sound coming from
the corresponding speakers seems to be at the same level as that
from the main speakers when you are at a normal listening position.
If there is insufficient volume from the effect speakers, you may
decrease the main speaker volume level by using the MAIN LEVEL
control on the rear panel and adjust the center and rear level again.
Volume controls on external power amplifiers may also be adjusted if
necessary to achieve proper balance.
3.
For the front effect speaker level adjustment, depress the TEST
switch on the remote control again so that “TEST DSP” appears in
the display panel. A calibration signal should be heard from the main
speakers and the front effect speakers in turn (see diagram).
4.
Adjust the front level by using the FRONT LEVEL +/– keys on the
remote control so that the speaker volume is the same as that of the
main speakers.
NOTE:
If not using a center speaker, be sure to set the CENTER
MODE to the PHNTM (phantom) position. You will then hear the
center channel test tone from the left and right main speakers.
After completing this adjustment, press the TEST switch once
again.
NOTE:
Once you have completed these adjustments, use only this
unit’s MASTER VOLUME control to adjust listening volume. Do not
change any other volume settings in the system.
23
Left main
Center
Right main
Rear
LEFT
CENTER
RIGHT
SURROUND
Main
Front
MAIN
FRONT