Yamaha DSP-A990 Owner's Manual - Page 13

Audio Signal Connection Jacks for Audio Source Equipment - amplifier

Get Yamaha DSP-A990 PDF manuals and user guides View all Yamaha DSP-A990 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

English 1 Audio Signal Connection Jacks (for Audio Source Equipment) Connect the inputs and/or outputs of your audio equipment. 2 Audio/Video Signal Connection Jacks (for Video Source Equipment) Connect the audio and video inputs and/or outputs of your video equipment. In place of the VIDEO jacks, the S VIDEO jacks can be used for higher resolution and improved picture quality if your VCR, monitor, etc. are equipped with S-VIDEO connectors. 3 Main Level Switch Normally set to "0 dB". If desired, you can decrease the mainchannel output level at the MAIN speaker terminals by 10 dB by setting this switch to "-10 dB". 4 Pre Out Jacks Main-channel line output. Connected with jumper bars to MAIN IN jacks when the built-in amplifier is used. Connected to input jacks of external stereo power amplifier (MAIN IN or TAPE PLAY jacks of integrated amplifier or receiver) when using external amplification. 5 Main In Jacks Line input to built-in main-channel amplifier. Connected with jumper bars to PRE OUT jacks when the built-in amplifier is used. Not connected when using an external power amplifier. 6 Main Speaker Terminals When using this unit's built-in main-channel amplifier, connect the main speakers here. The jumper bars must be plugged in to connect the MAIN IN jacks to the PRE OUT jacks. 7 Front Effect Speaker Terminals When using the built-in front-channel amplifier, connect the front effect speakers here. 8 Center Speaker Terminals When using the built-in center-channel amplifier, connect one or two center speakers here. 9 Center Speaker Impedance Switch Set to "A + B" when using two center speakers, or to "A OR B" when using only one center speaker. 0 Rear Effect Speaker Terminals When using the built-in rear-channel amplifier, connect the rear effect speakers here. A GND Terminal Connects the ground wire of the turntable to produce minimum hum. In some cases, however, better results may be obtained with the ground wire disconnected. B Video NTSC/PAL Switch (General Model only) Set this switch to the position corresponding to the standard that your video equipment employs. C Front Effect Out Jacks Front-channel line output. Not connected when the built-in amplifier is used. Can be connected to input jacks of an external stereo power amplifier driving the front effect speakers. D Front Mix Switch Set to "OFF (7ch)" when setting up a full 7 or 6 speaker system, or to "ON (5ch)" when setting up a 5 or 4 speaker system. E Rear Effect Out Jacks Rear-channel line output. Not connected when the built-in amplifier is used. Can be connected to input jacks of an external stereo power amplifier driving the rear effect speakers. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
11
English
1
Audio Signal Connection Jacks (for Audio Source Equipment)
Connect the inputs and/or outputs of your audio equipment.
2
Audio/Video Signal Connection Jacks (for Video Source
Equipment)
Connect the audio and video inputs and/or outputs of your video
equipment. In place of the VIDEO jacks, the S VIDEO jacks can
be used for higher resolution and improved picture quality if your
VCR, monitor, etc. are equipped with S-VIDEO connectors.
3
Main Level Switch
Normally set to “0 dB”. If desired, you can decrease the main-
channel output level at the MAIN speaker terminals by 10 dB by
setting this switch to “–10 dB”.
4
Pre Out Jacks
Main-channel line output. Connected with jumper bars to MAIN
IN jacks when the built-in amplifier is used. Connected to input
jacks of external stereo power amplifier (MAIN IN or TAPE PLAY
jacks of integrated amplifier or receiver) when using external
amplification.
5
Main In Jacks
Line input to built-in main-channel amplifier. Connected with
jumper bars to PRE OUT jacks when the built-in amplifier is used.
Not connected when using an external power amplifier.
6
Main Speaker Terminals
When using this unit’s built-in main-channel amplifier, connect the
main speakers here. The jumper bars must be plugged in to
connect the MAIN IN jacks to the PRE OUT jacks.
7
Front Effect Speaker Terminals
When using the built-in front-channel amplifier, connect the front
effect speakers here.
8
Center Speaker Terminals
When using the built-in center-channel amplifier, connect one or
two center speakers here.
9
Center Speaker Impedance Switch
Set to “A + B” when using two center speakers, or to “A OR B”
when using only one center speaker.
0
Rear Effect Speaker Terminals
When using the built-in rear-channel amplifier, connect the rear
effect speakers here.
A
GND Terminal
Connects the ground wire of the turntable to produce minimum
hum. In some cases, however, better results may be obtained
with the ground wire disconnected.
B
Video NTSC/PAL Switch (General Model only)
Set this switch to the position corresponding to the standard
that your video equipment employs.
C
Front Effect Out Jacks
Front-channel line output. Not connected when the built-in
amplifier is used. Can be connected to input jacks of an
external stereo power amplifier driving the front effect
speakers.
D
Front Mix Switch
Set to “OFF (7ch)” when setting up a full 7 or 6 speaker system,
or to “ON (5ch)” when setting up a 5 or 4 speaker system.
E
Rear Effect Out Jacks
Rear-channel line output. Not connected when the built-in
amplifier is used. Can be connected to input jacks of an
external stereo power amplifier driving the rear effect speakers.