Yamaha FX500 FX500 Owners Manual Image - Page 21
Parameter, Control, Control, Change, Table
View all Yamaha FX500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
• MIDI Setup This function makes it possible to select any of the four available program change table BANKs, and to change the MIDI receive channel for each BANK. 7/ 636 YAMAHA,.E00 1111111111111111111111111111111111111111111111111 MIDI SETUP BANK.A ch.OMNI 111111111111111111110111111111111111111111111N Use the UTILITY key to select the MIDI SETUP display. , MIDI SETUP BANK:A ch=0MNI 0 The underline cursor should be under the BANK parameter. Use the Aand Vkeys to select the bank you wish to program (A, B, C or D). 0 Move the cursor to the "ch=" parameter by pressing the PARAM (0.) key, then use the Aand Vkeys to set the receive MIDI channel (1 - 16), the OMNI mode (all channels can be received), or turn MIDI reception OFF for the selected bank. The underline cursor can be moved back to the BANK parameter if necessary by pressing the MEMORY (4) key. • Program Change Table Edit When this function is called the LCD will appear as shown below, and it becomes possible to assign new memory location numbers to each MIDI program change number. 0 a Eb[i"±-) C"±) YAMAHA ..00 111111111111111111111111111111111111111111101111 I MIDI PGM CHANGE PGN 1 . MEN 1 E5Et15 11110001111111111111111111111110001111111 // 0 CD (-) Use the UTILITY key to select the MIDI PGM CHANGE display. The underline cursor should be under the PGM parameter. MIDI PGM CHANGE PGM 1 = MEM 1 0 Use the Aand Vkeys to select the program change number to which a new FX500 memory location number is to be assigned. The range of available program change numbers is from 1 to 128. 0 Move the underline cursor to the MEM parameter by pressing the PARAM (O.) key. Use the Aand Vkeys to select the memory location number containing the effect which is to be assigned to the currently selected program change number. tf "--" is selected, no new memory location will be selected when that program number is received. ® Move the underline cursor back to the PGM parameter by pressing the MEMORY (4) key and repeat the above steps to assign as many program change numbers as necessary. NOTE: The program number/memory number assignments made are stored in the BANK selected in the previous MIDI Setup function. To program the program change/memory number assignments for a different BANK, return to the MIDI SETUP display, select the desired BANK, then program the required assignments. NOTE: Although the BANK A, B, and C program change tables are retained in memory even when the power is off, the BANK D program change table is automatically initialized whenever the FX500 power switch is turned on (PGM number = MEM number). Make sure you program PGM/MEM assignments you want to keep in BANK A, B, or C. • MIDIParameter Control: Control Change 1 Table Edit and Control Change 2 Table Edit The FX500 allows two MIDI "controllers" to be assigned for remote real-time control of effect parameters. "MIDI controller actually refers to a MIDI CONTROL CHANGE number between 0 and 127. Some of these numbers are assigned to specific controllers - modulation wheel, data entry, etc - and a MIDI device such as a keyboard or MFC1 MIDI Foot Controller that has the any of these controllers will transmit the corresponding MIDI control change data when the controllers are operated. You could, for example, assign an FC7 connected to an MFC1 to control the FX500 reverb time. FC7 MFC1 HUM MIDI OUT 00 0000 FC7can be assigned to control FX500 reverb time. MIDI IN 0. ,D._ . :: id6,5,,,,.,,.,,;ia:m.,6,E,,,.,,,,,, CI5ED" ..±21":, =Di= c) 11111111111111111111111111110111141141311.1.1 . 0 0.-- 0 - 0°.- 0°'"." 20