Yamaha HTR-5930 Owner's Manual - Page 64

TROUBLESHOOTING, General - problems

Get Yamaha HTR-5930 PDF manuals and user guides View all Yamaha HTR-5930 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

TROUBLESHOOTING TROUBLESHOOTING Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem This unit fails to turn on or enters the standby mode soon after the power is turned on. No sound Cause The power cable is not connected or the plug is not completely inserted. The speaker impedance setting is incorrect. The protection circuitry has been activated. This unit has been exposed to a strong external electric shock (such as lightning or strong static electricity). Incorrect input or output cable connections. No appropriate input mode has been selected. No appropriate input source has been selected. Speaker connections are not secure. The front speakers to be used have not been selected properly. The volume is turned down. The sound is muted. Signals this unit cannot reproduce are being input from a source component, such as a CD-ROM. Remedy Connect the power cable firmly. Set the speaker impedance to match your speakers. Make sure that all speaker wire connections on this unit and on all speakers are secure and that the wire for each connection does not touch anything other than its respective connection. Set this unit to the standby mode, disconnect the power cable, plug it back in after 30 seconds and then use it normally. Connect the cables properly. If the problem persists, the cables may be defective. Select an appropriate input mode. Select an appropriate input source with INPUT l / h on the front panel (or the input selector buttons on the remote control) and MULTI CH INPUT on the front panel (or MULTI CH IN on the remote control). Secure the connections. Select the front speakers with SPEAKERS on the front panel or SPEAKERS A/B on the remote control. Turn up the volume. Press MUTE or VOLUME +/- on the remote control to resume audio output and then adjust the volume. Play a source whose signals can be reproduced by this unit. See page - 9, 11 11 - 13-17 26 23, 25 11 23 - 25 - 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
TROUBLESHOOTING
60
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
YAMAHA dealer or service center.
■
General
TROUBLESHOOTING
Problem
Cause
Remedy
See
page
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
—
The speaker impedance setting is
incorrect.
Set the speaker impedance to match your speakers.
9, 11
The protection circuitry has been
activated.
Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wire
for each connection does not touch anything other
than its respective connection.
11
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and then
use it normally.
—
No sound
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
13-17
No appropriate input mode has been
selected.
Select an appropriate input mode.
26
No appropriate input source has been
selected.
Select an appropriate input source with INPUT
l
/
h
on the front panel (or the input selector buttons on
the remote control) and MULTI CH INPUT on the
front panel (or MULTI CH IN on the remote control).
23, 25
Speaker connections are not secure.
Secure the connections.
11
The front speakers to be used have not
been selected properly.
Select the front speakers with SPEAKERS on the
front panel or SPEAKERS A/B on the remote control.
23
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press MUTE or VOLUME +/– on the remote control
to resume audio output and then adjust the volume.
25
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—