Yamaha MA2120 MA2120 Setup Guide - Page 12

Adjusting the Ducker Sensitivity, Regulating BGM Volume (Leveler)

Get Yamaha MA2120 PDF manuals and user guides View all Yamaha MA2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Setup Mode (Advanced settings) „ Adjusting the Ducker Sensitivity You can adjust the sensitivity of the ducker function. When there is an input signal to [INPUT 1] or [INPUT 3], this function can mute the microphone input for channels outside that particular output zone, or lower their line input volume by 24dB. The ducker input sensitivity can be set to "Low", "Mid", or "High". NOTE The ducker function can be turned on or off by switching [SETUP] DIP switches 7 and 8 when the device is powered off or in standby mode. For more information, refer to "Controls and Functions" of the owner's manual, or "List of DIP Switch Settings" on page 15. 3 2 1, 4, 5 1 Press and hold the [SETUP] encoder for at least one second. 2 Press input level knob 7. 3 Press input level knob 1, or input level knob 3 to select to which input channel you would like to adjust the sensitivity of ducker function. 4 Turn the [SETUP] encoder to adjust the ducker sensitivity. The parameter value changes with each click of the encoder. Low: Mid: (Default setting) High: 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). „ Regulating BGM Volume (Leveler) You can select the target level for the leveler function. This function adjusts the volume to an almost constant range when there are [INPUT 7]/[INPUT 8] input signals that have a significant variation in volume. The leveler function can be used to adjust a signal with a range of up to ±6dB. The target level can be set to "Off," "Low" or "Normal." NOTE Channels with the leveler function enabled have an output signal delay of approximately 20ms due to the required arithmetic processing. 3 2 1, 4, 5 1 Press and hold the [SETUP] encoder for at least one second. 2 Press input level knob 8. 3 Press input level knob 7, or input level knob 8 to select to which input channel you would like to apply the leveler function. 4 Turn the [SETUP] encoder to select the target level. Off: (Default setting) Low: Normal: 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). 12 MA2120 Setup Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
Setup Mode (Advanced settings)
12
MA2120 Setup Guide
±
Adjusting the Ducker Sensitivity
You can adjust the sensitivity of the ducker function. When there is an input signal to [INPUT 1] or [INPUT 3], this function can mute the
microphone input for channels outside that particular output zone, or lower their line input volume by 24dB.
The ducker input sensitivity can be set to “Low”, “Mid”, or “High”.
NOTE
The ducker function can be turned on or off by switching [SETUP] DIP switches 7 and 8 when the device is powered off or in standby
mode.
For more information, refer to “Controls and Functions” of the owner's manual, or “List of DIP Switch Settings” on page 15.
1
Press and hold the [SETUP] encoder for at least
one second.
2
Press input level knob 7.
3
Press input level knob 1, or input level knob 3 to
select to which input channel you would like to
adjust the sensitivity of ducker function.
4
Turn the [SETUP] encoder to adjust the ducker
sensitivity.
The parameter value changes with each click of the
encoder.
5
Press the [SETUP] encoder to apply the setting.
The status is back to the channel select (Step 3).
±
Regulating BGM Volume (Leveler)
You can select the target level for the leveler function. This function adjusts the volume to an almost constant range when there are
[INPUT 7]/[INPUT 8] input signals that have a significant variation in volume.
The leveler function can be used to adjust a signal with a range of up to ±6dB. The target level can be set to “Off,” “Low” or “Normal.”
NOTE
Channels with the leveler function enabled have an output signal delay of approximately 20ms due to the required arithmetic processing.
1
Press and hold the [SETUP] encoder for at least
one second.
2
Press input level knob 8.
3
Press input level knob 7, or input level knob 8 to
select to which input channel you would like to
apply the leveler function.
4
Turn the [SETUP] encoder to select the target
level.
5
Press the [SETUP] encoder to apply the setting.
The status is back to the channel select (Step 3).
2
3
1, 4, 5
Low:
Mid:
(Default setting)
High:
3
2
1, 4, 5
Off:
(Default setting)
Low:
Normal: